- 您现在的位置：买卖IC网 > PDF目录1840 > MAX1845EEI+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 28-QSOP PDF资料下载
参数资料
| 型号： | MAX1845EEI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/27页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 540kHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Dual, High-Efficiency, Step-Down
Controller with Accurate Current Limit
Pin Description (continued)
PIN
NAME
FUNCTION
QSOP
QFN
—
—
24
23
24
26
AGND
PGND
DL1
Analog Ground. Serves as negative input for CS_ amplifiers. Connect backside pad to AGND.
Power Ground
Low-Side Gate-Driver Output for OUT1. DL1 swings from PGND to V DD .
Boost Flying Capacitor Connection for OUT1. Connect to an external capacitor and diode according
25
27
BST1
to the standard application circuit in Figure 1. See the MOSFET Gate Drivers (DH_, DL_)
section.
26
27
28
30
DH1
LX1
High-Side Gate Driver Output for OUT1. Swings from LX1 to BST1.
External Inductor Connection for OUT1. Connect to the switched side of the inductor. LX1 serves
as the internal lower supply voltage rail for the DH1 high-side gate driver.
Current-Sense Input for OUT1. CS1 is the input to the current-limiting circuitry for valley current
28
31
CS1
limiting. For lowest cost and highest efficiency, connect to LX1. For highest accuracy, use a sense
resistor. See the Current-Limit Circuit (ILIM_) section.
6, 9, 10,
—
17, 25,
N.C.
No Connection
29, 36
Standard Application Circuit
The standard application circuit (Figure 1) generates a
1.8V and a 2.5V rail for general-purpose use in note-
book computers.
See Table 1 for component selections. Table 2 lists
component manufacturers.
Detailed Description
The MAX1845 buck controller is designed for low-volt-
age power supplies for notebook computers. Maxim’s
proprietary Quick-PWM pulse-width modulator in the
MAX1845 (Figure 2) is specifically designed for han-
dling fast load steps while maintaining a relatively con-
stant operating frequency and inductor operating point
over a wide range of input voltages. The Quick-PWM
architecture circumvents the poor load-transient timing
problems of fixed-frequency current-mode PWMs while
avoiding the problems caused by widely varying
switching frequencies in conventional constant-on-time
and constant-off-time PWM schemes.
5V Bias Supply (V CC and V DD )
The MAX1845 requires an external 5V bias supply in
addition to the battery. Typically, this 5V bias supply is
the notebook ’s 95% efficient 5V system supply.
Keeping the bias supply external to the IC improves
efficiency and eliminates the cost associated with the
5V linear regulator that would otherwise be needed to
supply the PWM circuit and gate drivers. If stand-alone
capability is needed, the 5V supply can be generated
with an external linear regulator such as the MAX1615.
The power input and 5V bias inputs can be connected
together if the input source is a fixed 4.5V to 5.5V sup-
ply. If the 5V bias supply is powered up prior to the bat-
tery supply, the enable signal (ON1, ON2) must be
delayed until the battery voltage is present to ensure
startup. The 5V bias supply must provide V CC and
gate-drive power, so the maximum current drawn is:
I BIAS = I CC + f (Q G1 + Q G2 ) = 5mA to 30mA (typ)
where I CC is 1mA typical, f is the switching frequency,
and Q G1 and Q G2 are the MOSFET data sheet total
gate-charge specification limits at V GS = 5V.
Free-Running, Constant-On-Time PWM
Controller with Input Feed-Forward
The Quick-PWM control architecture is a pseudo-fixed-
frequency, constant-on-time current-mode type with
voltage feed-forward (Figure 3). This architecture relies
on the output filter capacitor’s effective series resis-
tance (ESR) to act as a current-sense resistor, so the
output ripple voltage provides the PWM ramp signal.
The control algorithm is simple: the high-side switch on-
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1847EEE+T | IC REG CTRLR FLYBK INV CM 16QSOP |
| MAX1853EXT-T | IC REG SWITCHED CAP INV SC70-6 |
| MAX1856EUB | IC PS PWM SLIC SYNCH 10-UMAX |
| MAX1857EUA47+ | IC REG LDO 4.75V/ADJ .5A 8-UMAX |
| MAX1858EEG+T | IC REG CTRLR BUCK PWM VM 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1845EEI+ | 功能描述:电流型 PWM 控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1845EEI+T | 功能描述:电流型 PWM 控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1845EEI-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1845EEI-TG05 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1845EEI-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。