- 您现在的位置：买卖IC网 > PDF目录1840 > MAX1845EEI+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 28-QSOP PDF资料下载
参数资料
| 型号： | MAX1845EEI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/27页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 540kHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Dual, High-Efficiency, Step-Down
Controller with Accurate Current Limit
Δ i
Δ t
=
V BATT -V OUT
L
I PEAK
I PEAK
I LOAD
I LOAD = I PEAK /2
I LIMIT
0 ON-TIME
TIME
0
TIME
Figure 4. Pulse-Skipping/Discontinuous Crossover Point
be a low-resistance, low-inductance path from the DL
driver to the MOSFET gate for the adaptive dead-time
circuit to work properly. Otherwise, the sense circuitry
in the MAX1845 will interpret the MOSFET gate as “off”
while there is actually still charge left on the gate. Use
very short, wide traces measuring 10 to 20 squares (50
to 100 mils wide if the MOSFET is 1 inch from the
MAX1845).
The dead time at the other edge (DH turning off) is
determined by a fixed 35ns (typ) internal delay.
The internal pulldown transistor that drives DL low is
robust, with a 0.5 Ω typical on-resistance. This helps
prevent DL from being pulled up during the fast rise-
time of the inductor node, due to capacitive coupling
from the drain to the gate of the low-side synchronous-
rectifier MOSFET. However, for high-current applica-
tions, some combinations of high- and low-side FETs
might be encountered that will cause excessive gate-
drain coupling, which can lead to efficiency-killing,
EMI-producing shoot-through currents. This is often
remedied by adding a resistor in series with BST, which
increases the turn-on time of the high-side FET without
degrading the turn-off time (Figure 6).
POR, UVLO, and Soft-Start
Power-on reset (POR) occurs when V CC rises above
approximately 2V, resetting the fault latch and soft-start
counter and preparing the PWM for operation. V CC
undervoltage lockout (UVLO) circuitry inhibits switch-
ing. DL is low if the overvoltage protection (OVP) is dis-
abled. DL is high if the overvoltage protection is
enabled (see the Output Overvoltage Protection sec-
tion) when V CC rises above 4.2V, whereupon an inter-
nal digital soft-start timer begins to ramp up the
maximum allowed current limit. The ramp occurs in five
steps: 20%, 40%, 60%, 80%, and 100%; 100% current
is available after 1.7ms ±50%.
Figure 5. ‘‘Valley’’ Current-Limit Threshold Point
A continuously adjustable analog soft-start function can
be realized by adding a capacitor in parallel with the
ILIM external resistor-divider network. This soft-start
method requires a minimum interval between power-
down and power-up to discharge the capacitor.
Power-Good Output (PGOOD)
The PGOOD window comparator continuously monitors
the output voltage for both overvoltage and undervolt-
age conditions. In shutdown, standby, and soft-start,
PGOOD is actively held low. After a digital soft-start
has terminated, PGOOD is released when the output is
within 10% of the error-comparator threshold. The
PGOOD output is a true open-drain type with no para-
sitic ESD diodes. Note that the PGOOD window detec-
tor is independent of the output overvoltage and
undervoltage protection (UVP) thresholds.
Output Overvoltage Protection
The output voltage can be continuously monitored for
overvoltage. When overvoltage protection is enabled, if
the output exceeds the overvoltage threshold, overvolt-
age protection is triggered and the DL low-side gate-
drivers are forced high. This activates the low-side
MOSFET switch, which rapidly discharges the output
capacitor and reduces the input voltage.
Note that DL latching high causes the output voltage to
dip slightly negative when energy has been previously
stored in the LC tank circuit. For loads that cannot toler-
ate a negative voltage, place a power Schottky diode
across the output to act as a reverse polarity clamp.
Connect OVP to GND to enable the default trip level of
114% of the nominal output. To adjust the overvoltage
protection trip level, apply a voltage from 1V (100%) to
1.8V (180%) at OVP. Disable the overvoltage protection
by connecting OVP to V CC .
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1847EEE+T | IC REG CTRLR FLYBK INV CM 16QSOP |
| MAX1853EXT-T | IC REG SWITCHED CAP INV SC70-6 |
| MAX1856EUB | IC PS PWM SLIC SYNCH 10-UMAX |
| MAX1857EUA47+ | IC REG LDO 4.75V/ADJ .5A 8-UMAX |
| MAX1858EEG+T | IC REG CTRLR BUCK PWM VM 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1845EEI+ | 功能描述:电流型 PWM 控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1845EEI+T | 功能描述:电流型 PWM 控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1845EEI-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1845EEI-TG05 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1845EEI-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。