- 您现在的位置：买卖IC网 > PDF目录1841 > MAX1857EUA47+ (Maxim Integrated Products)IC REG LDO 4.75V/ADJ .5A 8-UMAX PDF资料下载
参数资料
| 型号： | MAX1857EUA47+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 4.75V/ADJ .5A 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式或可调式 |
| 输出电压： | 4.75V，1.25 V ~ 5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA（最小） |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
| 产品目录页面： | 1410 (CN2011-ZH PDF) |
500mA, Low-Dropout,
Ripple-Rejecting LDO in μMAX
Detailed Description
The MAX1857 is a low-dropout, low-quiescent-current
ripple rejector designed primarily for audio and video
applications. The device supplies loads up to 500mA
IN
OUT
R1 = R2
V OUT
1.25V
-1
and is available with a preset output voltage of 4.75V.
As shown in Figure 1, the MAX1857 consists of a 1.25V
V IN = +2.5V TO +5.5V
IN
OUT
V OUT
reference, error amplifier, P-channel pass transistor,
and internal feedback voltage-divider.
The 1.25V reference is connected to the error amplifier,
C IN
1 μ F
MAX1857
C OUT
3.3 μ F
R 1
which compares this reference with the feedback volt-
age and amplifies the difference. If the feedback volt-
age is lower than the reference voltage, the
pass-transistor gate is pulled lower, which allows more
ON
OFF
SHDN
SET
current to pass to the output and increases the output
voltage. If the feedback voltage is too high, the pass-
R 2
transistor gate is pulled up, allowing less current to
pass to the output.
The output voltage is fed back through either an inter-
nal resistive divider connected to OUT or an external
RST
GND
resistor network connected to SET. The dual-mode
comparator examines V SET and selects the feedback
path. If V SET is below 50mV, the internal feedback path
is used and the output is regulated to the factory-preset
voltage.
Additional blocks include an output current limiter,
reset comparator, thermal sensor, and shutdown logic.
Internal P-Channel Pass Transistor
The MAX1857 features a 0.25 ? P-channel MOSFET
pass transistor. Unlike similar designs using PNP pass
transistors, P-channel MOSFETs require no base drive,
which reduces quiescent current. PNP-based regula-
tors also waste considerable current in dropout when
the pass transistor saturates, and use high base-drive
currents under large loads. The MAX1857 does not suf-
fer from these problems and consumes only 175μA of
quiescent current under heavy loads as well as in
dropout.
Output Voltage Selection
The MAX1857 ’ s dual-mode operation allows operation
in either a preset voltage mode or an adjustable mode.
Connect SET to GND to select the preset output volt-
age. The two-digit part number suffix identifies the out-
put voltage (see Selector Guide ). For example, the
MAX1857EUA47 has a preset 4.75V output voltage.
The output voltage may also be adjusted by connecting
a voltage-divider from OUT to SET (Figure 2). Select R2
Figure 2. Adjustable Output Using External Feedback
Resistors
in the 25k ? to 100k ? range. Calculate R1 with the fol-
lowing equation:
R1 = R2 [(V OUT / V SET ) – 1]
where V SET = 1.25V, and V OUT may range from 1.25V
to 5.0V.
Shutdown
Pull SHDN low to enter shutdown. During shutdown, the
output is disconnected from the input and supply current
drops to 0.1μA. When in shutdown, RST pulls low and
OUT is discharged through an internal 5k ? resistor. The
capacitance and load at OUT determine the rate at
which V OUT decays. SHDN can be pulled as high as 6V,
regardless of the input and output voltage.
Reset Output
The reset output ( RST ) pulls low when OUT is less than
86% of the nominal regulation voltage. Once OUT
exceeds 86% of the nominal voltage, RST goes high
impedance after 4.5ms. RST is an open-drain N-channel
output. To obtain a voltage at RST , connect a pullup
resistor from RST to OUT. A 100k ? resistor works well for
most applications. RST can be used as a power-on-reset
(POR) signal to a microcontroller (μC), or drive an exter-
nal LED to indicate power failure. When the MAX1857 is
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1858EEG+T | IC REG CTRLR BUCK PWM VM 24-QSOP |
| MAX1865TEEP+T | IC PWR SUPPLY CONTROLLER 20QSOP |
| MAX1873REEE+T | IC CNTRLR CHARGE LI+ 16-QSOP |
| MAX1874ETE+ | IC LI+ CHARGER DUAL-IN 16-TQFN |
| MAX1875AEEG+ | IC REG CTRLR BUCK PWM VM 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1857EUA47+ | 功能描述:低压差稳压器 - LDO 500mA Ripple-Rejecting RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX1857EUA47+T | 功能描述:低压差稳压器 - LDO 500mA Ripple-Rejecting RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX1857EUA47-T | 功能描述:低压差稳压器 - LDO 500mA Ripple-Rejecting RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX1858AEEG | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1858AEEG+ | 功能描述:电压模式 PWM 控制器 Dual 180 Out Buck Controllers RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。