- 您现在的位置：买卖IC网 > PDF目录9507 > MAX186DCPP+ (Maxim Integrated Products)IC DAS 8CH 12BIT T/H LP 20-DIP PDF资料下载
参数资料
| 型号： | MAX186DCPP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/25页 |
| 文件大小： | 0K |
| 描述： | IC DAS 8CH 12BIT T/H LP 20-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 18 |
| 类型： | 数据采集系统（DAS），ADC |
| 分辨率（位）： | 12 b |
| 采样率（每秒）： | 133k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 电压电源： | 双 ± |
| 电源电压： | ±5V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 1393 (CN2011-ZH PDF) |
Data Framing
The falling edge of CS does not start a conversion on the
MAX186/MAX188. The first logic high clocked into DIN is
interpreted as a start bit and defines the first bit of the
control byte. A conversion starts on the falling edge of
SCLK, after the eighth bit of the control byte (the PD0 bit)
is clocked into DIN. The start bit is defined as:
The first high bit clocked into DIN with CS low any-
time the converter is idle, e.g. after VCC is applied.
OR
The first high bit clocked into DIN after bit 5 of a
conversion in progress is clocked onto the DOUT pin.
If a falling edge on CS forces a start bit before bit 5
(B5) becomes available, then the current conversion
will be terminated and a new one started. Thus, the
fastest the MAX186/MAX188 can run is 15 clocks per
conversion. Figure 11a shows the serial-interface timing
necessary to perform a conversion every 15 SCLK
cycles in external clock mode. If CS is low and SCLK is
continuous, guarantee a start bit by first clocking in 16
zeros.
Most microcontrollers require that conversions occur in
multiples of 8 SCLK clocks; 16 clocks per conversion
will typically be the fastest that a microcontroller can
drive the MAX186/MAX188. Figure 11b shows the
serial-interface timing necessary to perform a conver-
sion every 16 SCLK cycles in external clock mode.
__________ Applications Information
Power-On Reset
When power is first applied and if SHDN is not pulled
low, internal power-on reset circuitry will activate the
MAX186/MAX188 in internal clock mode, ready to con-
vert with SSTRB = high. After the power supplies have
been stabilized, the internal reset time is 100s and no
conversions should be performed during this phase.
SSTRB is high on power-up and, if CS is low, the first
logical 1 on DIN will be interpreted as a start bit. Until a
conversion takes place, DOUT will shift out zeros.
Reference-Buffer Compensation
In addition to its shutdown function, the SHDN pin also
selects internal or external compensation. The compen-
sation affects both power-up time and maximum conver-
sion speed. Compensated or not, the minimum clock
rate is 100kHz due to droop on the sample-and-hold.
To select external compensation, open SHDN. See the
Typical Operating Circuit, which uses a 4.7F capacitor at
VREF. A value of 4.7F or greater ensures stability and
allows operation of the converter at the full clock speed of
2MHz. External compensation increases power-up time (see
the
Choosing Power-Down Mode section, and Table 5).
Internal compensation requires no external capacitor at
VREF, and is selected by pulling SHDN high. Internal com-
pensation allows for shortest power-up times, but is only
available using an external clock and reduces the maxi-
mum clock rate to 400kHz.
Low-Power, 8-Channel,
Serial 12-Bit ADCs
14
Maxim Integrated
MAX186/MAX188
PD0 CLOCK IN
tSSTRB
tCSH
tCONV
tSCK
SSTRB
SCLK
tCSS
NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION.
CS
Figure 10. Internal Clock Mode SSTRB Detailed Timing
相关PDF资料 |
PDF描述 |
|---|---|
| MAX188DCPP+ | IC DAS 8CH 12BIT T/H LP 20-DIP |
| M83723/78R1407N | CONN PLUG 7POS STRAIGHT W/PINS |
| D38999/26WB98SD | CONN PLUG 6POS STRAIGHT W/SCKT |
| AD7606BSTZ-6RL | IC DAS W/ADC 16BIT 64LQFP |
| MS27473T20F16SA | CONN PLUG 16POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX186DCPP+ | 功能描述:模数转换器 - ADC 12-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX186DCWP | 功能描述:模数转换器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX186DCWP+ | 功能描述:模数转换器 - ADC 12-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX186DCWP+T | 功能描述:模数转换器 - ADC 12-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX186DCWP-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。