- 您现在的位置：买卖IC网 > PDF目录15488 > MAX1875EEG+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM VM 24-QSOP PDF资料下载
参数资料
| 型号： | MAX1875EEG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/21页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 24-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 660kHz |
| 占空比： | 90% |
| 电源电压： | 4.75 V ~ 23 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
Dual 180° Out-of-Phase PWM Step-
Down Controllers with POR
Pin Description
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
NAME
COMP2
FB2
ILIM2
OSC
V+
REF
GND
CKO
SYNC
ILIM1
FB1
COMP1
RST
FUNCTION
Compensation Pin for Regulator 2 (REG2). Compensate REG2 ’ s control loop by connecting a series
resistor (R COMP2 ) and capacitor (C COMP2A ) to GND in parallel with a second compensation capacitor
(C COMP2B ) as shown in Figure 1.
Feedback Input for Regulator 2 (REG2). Connect FB2 to a resistive-divider between REG2 ’ s output
and GND to adjust the output voltage between 1V and 18V. To set the output voltage below 1V,
connect FB2 to a resistive voltage-divider from REF to REG2 ’ s output. See the Setting the Output
Voltage section.
Current-Limit Adjustment for Regulator 2 (REG2). The PGND – LX2 current-limit threshold defaults to
100mV if ILIM2 is connected to V L . Connect a resistor (R ILIM2 ) from ILIM2 to GND to adjust the
REG2 ’ s current-limit threshold (V ITH2 ) from 50mV (R ILIM2 = 100k ? ) to 300mV (R ILIM2 = 600k ? ). See
the Setting the Valley Current Limit section.
Oscillator Frequency Set Input. The controller generates the clock signal by dividing down the
oscillator, so the switching frequency equals half the synchronization frequency (f SW = f OSC /2).
Connect a resistor from OSC to GND (R OSC ) to set the switching frequency from 100kHz (R OSC =
60k ? ) to 600kHz (R OSC = 10k ? ). The controller still requires R OSC when an external clock is
connected to SYNC. When using SYNC, set R OSC for one half of the SYNC input.
Input Supply Voltage. 4.75V to 23V.
2V Reference Output. Bypass to GND with a 0.22μF or greater ceramic capacitor.
Analog Ground
Clock Output. Clock Output for external 2- or 4-phase synchronization (see the Clock Synchronization
(SYNC, CKO) section).
Synchronization Input or Clock Output Selection Input. SYNC has three operating modes. Connect
SYNC to a 200kHz to 1200kHz clock for external synchronization. Connect SYNC to GND for 2-phase
operation as a master controller. Connect SYNC to V L for 4-phase operation as a master controller
(see the Clock Synchronization (SYNC, CKO) section).
Current-Limit Adjustment for Regulator 1 (REG1). The PGND – LX1 current-limit threshold defaults to
100mV if ILIM1 is connected to V L . Connect a resistor (R ILIM1 ) from ILIM1 to GND to adjust REG1 ’ s
current-limit threshold (V ITH1 ) from 50mV (R ILIM1 = 100k ? ) to 300mV (R ILIM1 = 600k ? ). See the
Setting the Valley Current Limit section.
Feedback Input for Regulator 1 (REG1). Connect FB1 to a resistive-divider between REG1 ’ s output
and GND to adjust the output voltage between 1V and 18V. To set the output voltage below 1V,
connect FB1 to a resistive voltage-divider from REF and REG1 ’ s output. See the Setting the Output
Voltage section.
Compensation Pin for Regulator 1 (REG1). Compensate REG1 ’ s control loop by connecting a series
resistor (R COMP1 ) and capacitor (C COMP1A ) to GND in parallel with a second compensation capacitor
(C COMP1B ) as shown in Figure 1.
Open-Drain Reset Output (MAX1876 only). RST is low when either output voltage is more than 10%
below its regulation point. After soft-start is completed and both outputs exceed 90% of their nominal
output voltage (V FB _ > 0.9V), RST becomes high impedance after a 140ms delay and remains high
impedance as long as both outputs maintain regulation. Connect a resistor between RST and the
logic supply for logic-level voltages.
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JV2-EY-B1 | CONVERTER MOD DC/DC 15V 50W |
| MAX5003CEE+ | IC REG CTRLR FLYBK ISO VM 16QSOP |
| URU1J221MHD | CAP ALUM 220UF 63V 20% RADIAL |
| MAX1960EEP+ | IC REG CTRLR BUCK PWM VM 20-QSOP |
| MAX15046AAEE+ | IC REG CTRLR BUCK PWM VM 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1875EEG+ | 功能描述:电压模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1875EEG+T | 功能描述:电压模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1875EEG-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1875EVKIT | 功能描述:DC/DC 开关控制器 Evaluation Kit for the MAX1875 MAX1876 MAX1858 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1876AEEG | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。