参数资料
| 型号： | MAX1945REUI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/19页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 6A 28TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 两者兼有 |
| 输出数： | 1 |
| 输出电压： | 1.8V，2.5V，可调 |
| 输入电压： | 2.6 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 400kHz ~ 1.2MHz |
| 电流 - 输出： | 6A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
1MHz, 1% Accurate, 6A Internal Switch
Step-Down Regulators
Use a low-loss inductor with the lowest possible DC
resistance that fits in the allotted dimensions. Ferrite
core types are often the best choice for performance.
With any core material the core must be large enough
not to saturate at the peak inductor current (I PEAK ).
I OUT(MAX) = 6A
LIR = 30%
L = 1μH
C OUT = 180μF
I PEAK = ? 1 +
? I OUT ( MAX )
?
?
LIR ?
2 ?
ESR (OUTPUT CAPACITOR) = 30m ?
ESL (OUTPUT CAPACITOR) = 2.5nH
V RIPPLE(C) = 2mV
Example:
V IN = 3.3V
V OUT = 1.8V
f OSC = 500kHz
I OUT(MAX) = 6A
LIR = 30%
L = 1μH and I PEAK = 6.9A
Output Capacitor Selection
The key selection parameters for the output capacitor
are capacitance, ESR, ESL, and voltage rating require-
ments. These affect the overall stability, output ripple
voltage, and transient response of the DC-DC convert-
er. The output ripple occurs because of variations in
the charge stored in the output capacitor, the voltage
drop due to the capacitor’s ESR, and the voltage drop
due to the capacitor’s ESL. Calculate the output voltage
ripple due to the output capacitance, ESR, and ESL as:
V RIPPLE = V RIPPLE(C) + V RIPPLE(ESR) + V RIPPLE(ESL)
where the output ripple due to output capacitance,
ESR, and ESL are:
V RIPPLE(C) = I P-P /(8 ? C OUT ? f SW ), V RIPPLE(ESR) = I P-P ?
ESR
V RIPPLE(ESL) = (I P-P /t ON ) ? ESL or (I P-P /t OFF ) ? ESL,
whichever is greater
The peak inductor current (I P-P ) is:
I P-P = ((V IN - V OUT )/(f SW ? L )) ? (V OUT /V IN )
V RIPPLE(ESR) = 45mV
V RIPPLE(ESL) = 4mV
V RIPPLE = 51mV
Use these equations for initial capacitor selection.
Determine final values by testing a prototype or an
evaluation circuit. A smaller ripple current results in less
output voltage ripple. Because the inductor ripple cur-
rent is a factor of the inductor value, the output voltage
ripple decreases with a larger inductance. Use ceramic
capacitors for low ESR and low ESL at the switching
frequency of the converter. The low ESL of ceramic
capacitors makes ripple voltages negligible. Load tran-
sient response depends on the selected output. During
a load transient, the output instantly changes by ESR ?
I LOAD . Before the controller can respond, the output
deviates further, depending on the inductor and output
capacitor values. After a short time (see the Transient
Response graphs in the Typical Operating Character-
istics ), the controller responds by regulating the output
voltage back to its predetermined value. The controller
response time depends on the closed-loop bandwidth.
A higher bandwidth yields a faster response time, pre-
venting the output from deviating further from its regu-
lating value.
Input Capacitor Selection
The input capacitor reduces the current peaks drawn
from the input power supply and reduces switching noise
in the IC. The impedance of the input capacitor at the
switching frequency should be less than that of the input
source so that high-frequency switching currents do not
pass through the input source but instead are shunted
through the input capacitor. A high source impedance
requires larger input capacitance. The input capacitor
must meet the ripple current requirement imposed by the
switching currents. The RMS input ripple current is given
by:
OUT IN OUT )
× ( V ? V
I RIPPLE = I LOAD × ?
?
?
Example:
V IN = 3.3V
V OUT = 1.8V
? V
? V IN
?
?
?
f OSC = 500kHz
where I RIPPLE is the input RMS ripple current.
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1946ETA+T | IC USB SW SGL AUTORESET 8TDFN |
| MAX1947ETA25+T | IC REG BST SYNC 2.5V 0.25A 8TDFN |
| MAX1951AESA+T | IC REG BUCK SYNC ADJ 2A 8SOIC |
| MAX1951ESA+W | IC REG BUCK SYNC ADJ 2A 8SOIC |
| MAX1954AEUB+T | IC REG CTRLR BUCK PWM CM 10-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1945SEUI | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1945SEUI+ | 功能描述:直流/直流开关调节器 1MHz 1% 6A Step-Down PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1945SEUI+T | 功能描述:直流/直流开关调节器 1MHz 1% 6A Step-Down PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1945SEUI-T | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1946ETA | 制造商:Maxim Integrated Products 功能描述:SINGLE USB SWITCH WITH AUTORESET AND FAULT BL - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。