- 您现在的位置：买卖IC网 > PDF目录2087 > MAX194BEPE+ (Maxim Integrated Products)IC ADC 14BIT 85KSPS SHTDN 16-DIP PDF资料下载
参数资料
| 型号： | MAX194BEPE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 85KSPS SHTDN 16-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 25 |
| 位数： | 14 |
| 采样率（每秒）： | 85k |
| 数据接口： | QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 80mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
_______________Detailed Description
The MAX194 uses a successive-approximation register
(SAR) to convert an analog input to a 14-bit digital
code, which outputs as a serial data stream. The data
bits can be read either during the conversion, at the
CLK clock rate, or between conversions asynchronous
with CLK, at the SCLK rate (up to 5Mbps).
The MAX194 includes a capacitive digital-to-analog
converter (DAC) that provides an inherent track/hold
input. The interface and control logic are designed for
easy connection to most microprocessors (Ps), limiting
the need for external components. In addition to the
SAR and DAC, the MAX194 includes a serial interface, a
sampling comparator used by the SAR, ten calibration
DACs, and control logic for calibration and conversion.
The DAC consists of an array of capacitors with binary
weighted values plus one “dummy sub-LSB” capacitor
(Figure 1). During input acquisition in unipolar mode,
the array’s common terminal is connected to AGND
and all free terminals are connected to the input signal
(AIN). After acquisition, the common terminal is discon-
nected from AGND and the free terminals are discon-
nected from AIN, trapping a charge proportional to the
input voltage on the capacitor array.
The free terminal of the MSB (largest) capacitor is con-
nected to the reference (REF), which pulls the common
terminal (connected to the comparator) positive.
Simultaneously, the free terminals of all other capaci-
tors in the array are connected to AGND, which drives
the comparator input negative. If the analog input is
near VREF, connecting the MSB’s free terminal to REF
only pulls the comparator input slightly positive.
However, connecting the remaining capacitor’s free ter-
minals to ground drives the comparator input well
below ground, so that the comparator input is negative,
the comparator output is low, and the MSB is set high.
If the analog input is near ground, the comparator out-
put is high and the MSB is low.
Following this, the next largest capacitor is disconnect-
ed from AGND and connected to REF, and the com-
parator determines the next bit. This continues until all
bits have been determined. For a bipolar input range,
the MSB capacitor is connected to REF rather than AIN
during input acquisition, which results in an input range
of VREF to -VREF.
MAX194
14-Bit, 85ksps ADC with 10A Shutdown
_______________________________________________________________________________________
5
______________________________________________________________Pin Description
PIN
NAME
FUNCTION
1
BP/UP/SHDN
Bipolar/Unipolar/Shutdown Input. Three-state input selects bipolar or unipolar input range, or shutdown.
0V = shutdown, +5V = unipolar, floating = bipolar.
2
CLK
Conversion Clock Input
3
SCLK
Serial Clock Input is used to shift data out between conversions. May be asynchronous to CLK.
4
VDDD
+5V Digital Power Supply
5
DOUT
Serial Data Output, MSB first
6
DGND
Digital Ground
7
EOC
End-of-Conversion/Calibration Output—normally low. Rises at beginning of conversion or calibration and
falls at the end of either. May be used as an output framing signal.
8
CS
Chip-Select Input—active low. Enables the serial interface and the three-state data output (DOUT).
9
CONV
Convert-Start Input—active low. Conversion begins on the falling edge after CONV goes low if input signal
has been acquired; otherwise, on the falling clock edge after acquisition.
10
RESET
Reset Input. Pulling RESET low places ADC in inactive state. Rising edge resets control logic and begins
calibration.
11
VSSD
-5V Digital Power Supply
12
REF
Reference Input, 0 to 5V
13
AIN
Analog Input, 0 to VREF unipolar or ±VREF bipolar range
14
AGND
Analog Ground
15
VSSA
-5V Analog Power Supply
16
VDDA
+5V Analog Power Supply
相关PDF资料 |
PDF描述 |
|---|---|
| MAX19505ETM+T | IC ADC 8BIT 1CH 65MSPS 48TQFN |
| MAX19507ETM+T | IC ADC 8BIT 2CH 130MSPS 48TQFN |
| MAX19517ETM+T | IC ADC 10BIT 2CH 130MSPS 48TQFN |
| MAX19527EXE+T | IC ADC 12BIT 8CH 50MSPS 144CTBGA |
| MAX195BEPE+ | IC ADC 16BIT 85KSPS SHTDN 16-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX194BEPE+ | 功能描述:模数转换器 - ADC 14Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BEWE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BEWE+ | 功能描述:模数转换器 - ADC 14Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BEWE+T | 功能描述:模数转换器 - ADC 14Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BEWE-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。