参数资料
| 型号： | MAX1969EUI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC DRVR POWER 28-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 热电冷却器 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
Power Drivers for Peltier TEC Modules
Setting Voltage and Current Limits
Certain TEC parameters must be considered to guaran-
tee a robust design. These include maximum positive
current, maximum negative current, and the maximum
voltage allowed across the TEC. These limits should be
used to set the MAXIP, MAXIN, and MAXV voltages.
Setting Max Positive and
Negative TEC Current
MAXIP and MAXIN set the maximum positive and nega-
tive TEC currents, respectively. The default current limit
is ± 150mV / R SENSE when MAXIP and MAXIN are con-
nected to REF. To set maximum limits other than the
defaults, connect a resistor-divider from REF to GND to
set V MAXI_ . Use resistors in the 10k Ω to 100k Ω range.
V MAXI_ is related to I TEC by the following equations:
V MAXIP = 10(I TECP(MAX ) x R SENSE )
V MAXIN = 10(I TECN(MAX ) x R SENSE )
where I TECP(MAX) is the maximum positive TEC current
and I TECN(MAX) is the negative maximum TEC current.
Positive TEC current occurs when CS is less than OS1:
I TEC x R SENSE = V OS1 - V CS
when I TEC > 0.
I TEC x R SENSE = V CS - V OS1
when I TEC < 0.
The MAX1969 controls the TEC current in one direction
(unipolar current flow from OS1 to CS). Set the maxi-
mum unipolar TEC current by applying a voltage to
MAXIN. Connect MAXIP to MAXIN. The equation for
setting MAXIN is the same for the MAX1968 and
MAX1969.
Take care not to exceed the positive or negative cur-
rent limit on the TEC. Refer to the manufacturer’s data
sheet for these limits.
Setting MAX TEC Voltage
Apply a voltage to the MAXV pin to control the maxi-
mum differential TEC voltage. MAXV can vary from 0 to
REF. The voltage across the TEC is four times V MAXV
and can be positive or negative:
|V OS1 - V OS2 | = 4 x V MAXV
Set V MAXV with a resistor-divider between REF and
GND using resistors from 10k Ω to 100k Ω . V MAXV can
vary from 0 to REF.
Control Inputs/Outputs
Output Current Control
The voltage at CTLI directly sets the TEC current. CTLI
is typically driven from the output of a temperature con-
trol loop. For the purposes of the following equations, it
is assumed that positive TEC current is cooling (see
Figure 1). The transfer function relating current through
the TEC (I TEC ) and V CTLI is given by:
I TEC = (V CTLI - V REF )/(10 x R SENSE )
where V REF is 1.50V and:
I TEC = (V OS1 - V CS )/R SENSE
CTLI is centered around REF (1.50V). I TEC is zero when
CTLI = 1.50V. When VCTLI > 1.50V the MAX1968 is
cooling. Current flow is from OS2 to OS1. The voltages
on the pins relate as follows:
V OS2 > V OS1 > V CS
The opposite applies when heating. When V CTLI <
1.50V current flows from OS1 to OS2:
V OS2 < V OS1 < V CS
Shutdown Control
The MAX1968/MAX1969 can be placed in a power-sav-
ing shutdown mode by driving SHDN low. When the
MAX1968/MAX1969 are shut down, the TEC is off (OS1
and OS2 decay to GND) and supply current is reduced
to 2mA (typ).
ITEC Output
ITEC is a status output that provides a voltage proportion-
al to the actual TEC current. ITEC = REF when TEC cur-
rent is zero. The transfer function for the ITEC output is:
V ITEC = 1.50 + 8 x (V OS1 - V CS )
Use ITEC to monitor the cooling or heating current
through the TEC. The maximum capacitance that ITEC
can drive is 100pF.
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1971EEE+T | IC REG BUCK SYNC 0.75A DL 16QSOP |
| MAX1973EUB+T | IC REG BUCK SYNC ADJ 1A 10UMAX |
| MAX1977EEI+ | IC CNTRLR PS QUAD HI EFF 28QSOP |
| MAX1980ETP+ | IC REG CTRLR BUCK PWM 20-TQFN |
| MAX1983EUT+T | IC REG LDO ADJ .3A SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX196ACAI | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196ACAI+ | 功能描述:模数转换器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196ACAI+T | 功能描述:模数转换器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196ACAI-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196ACNI | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。