- 您现在的位置：买卖IC网 > PDF目录10741 > MAX19705ETM+T (Maxim Integrated Products)IC ANLG FRNT END 48-TQFN PDF资料下载
参数资料
| 型号： | MAX19705ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/37页 |
| 文件大小： | 0K |
| 描述： | IC ANLG FRNT END 48-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 10 |
| 通道数： | 4 |
| 功率（瓦特）： | 28.2mW |
| 电压 - 电源，模拟： | 2.7 V ~ 3.3 V |
| 电压 - 电源，数字： | 1.8 V ~ 3.3 V |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
MAX19705
10-Bit, 7.5Msps, Ultra-Low-Power
Analog Front-End
______________________________________________________________________________________
33
ADC Gain Error
Ideally, the ADC full-scale transition occurs at 1.5 LSB
below full scale. The gain error is the amount of devia-
tion between the measured transition point and the
ideal transition point with the offset error removed.
ADC Dynamic Parameter Definitions
Aperture Jitter
Figure 14 shows the aperture jitter (tAJ), which is the
sample-to-sample variation in the aperture delay.
Aperture Delay
Aperture delay (tAD) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 14).
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error) and results directly
from the ADC’s resolution (N bits):
SNR(max) = 6.02dB x N + 1.76dB (in dB)
In reality, there are other noise sources besides quanti-
zation noise: thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise. RMS noise includes all spec-
tral components to the Nyquist frequency excluding the
fundamental, the first five harmonics, and the DC offset.
Signal-to-Noise and Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to the RMS noise. RMS noise includes all spectral
components to the Nyquist frequency excluding the
fundamental and the DC offset.
Effective Number of Bits (ENOB)
ENOB specifies the dynamic performance of an ADC at a
specific input frequency and sampling rate. An ideal
ADC’s error consists of quantization noise only. ENOB for
a full-scale sinusoidal input waveform is computed from:
ENOB = (SINAD - 1.76) / 6.02
Total Harmonic Distortion (THD)
THD is typically the ratio of the RMS sum of the first five
harmonics of the input signal to the fundamental itself.
This is expressed as:
where V1 is the fundamental amplitude and V2–V6 are
the amplitudes of the 2nd- through 6th-order harmonics.
Third Harmonic Distortion (HD3)
HD3 is defined as the ratio of the RMS value of the third
harmonic component to the fundamental input signal.
Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio expressed in decibels of the RMS
amplitude of the fundamental (maximum signal compo-
nent) to the RMS value of the next-largest spurious
component, excluding DC offset.
Intermodulation Distortion (IMD)
IMD is the total power of the intermodulation products
relative to the total input power when two tones, f1 and
f2, are present at the inputs. The intermodulation prod-
ucts are (f1 ±f2), (2 f1), (2 f2), (2 f1 ±f2), (2 f2
±f1). The individual input tone levels are at -7dBFS.
3rd-Order Intermodulation (IM3)
IM3 is the power of the worst 3rd-order intermodulation
product relative to the input power of either input tone
when two tones, f1 and f2, are present at the inputs. The
3rd-order intermodulation products are (2 x f1 ±f2), (2
f2 ±f1). The individual input tone levels are at -7dBFS.
THD
(V + V +V +V +V )
V
2
3
2
4
2
5
2
6
2
1
=
20 x log
HOLD
ANALOG
INPUT
SAMPLED
DATA (T/H)
T/H
tAD
tAJ
TRACK
CLK
Figure 14. T/H Aperture Timing
相关PDF资料 |
PDF描述 |
|---|---|
| MAX978ESE+ | IC COMPARATOR QUAD 16-SOIC |
| MAX5866ETM+T | IC ANLG FRONT END 60MSPS 48-TQFN |
| MAX978EEE+ | IC COMPARATOR QUAD 16-QSOP |
| MAX913CPA+ | IC COMPARATOR TTL SNGL HS 8-DIP |
| ISL98002CRZ-140 | IC VID DIGITIZER 3CHN AFE 72-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX19705EVCMOD2 | 功能描述:ADC / DAC多通道 Evaluation System for the MAX19705 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19705EVCMODU | 功能描述:ADC / DAC多通道 Evaluation System for the MAX19705 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19705EVKIT | 功能描述:数据转换 IC 开发工具 Evaluation Kit for the MAX19705 MAX19706 MAX19707 MAX19708 RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX19706ETM | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19706ETM+ | 功能描述:ADC / DAC多通道 22Msps CODEC/AFE 1.8/2.7-3.3V RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
发布紧急采购，3分钟左右您将得到回复。