- 您现在的位置：买卖IC网 > PDF目录383343 > MAX1970 (Maxim Integrated Products, Inc.) Dual, 180∑ Out-of-Phase, 1.4MHz, 750mA Step- Down Regulator with POR and RSI/PFO PDF资料下载
参数资料
| 型号： | MAX1970 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual, 180∑ Out-of-Phase, 1.4MHz, 750mA Step- Down Regulator with POR and RSI/PFO |
| 中文描述： | 双路、180°异相、1.4MHz、750mA、降压型调节器，带有POR和RSI/PFO |
| 文件页数： | 14/20页 |
| 文件大小： | 371K |
| 代理商： | MAX1970 |
M
Design Procedure
Output Voltage Selection
Both output voltages can be selected in three different
ways as indicated by Table 1. Each output has two pre-
set voltages that can be set using FBSEL_ and it can
also be set to any voltage from 0.8V to V
IN
by using an
external resistor voltage-divider.
To use a resistor-divider to set the output voltage to
1.2V or higher (Figure 5), connect a resistor from FB_ to
OUT_ (R_
a
), and connect a resistor from FB_ to GND
(R_
b
). Select the value of R_
b
, between 10k
and
30k
. Then R_
a
is calculated by:
A resistor-divider can also be used to set the voltage of
one output from 0.8V to 1.2V. To do this, the other out-
put must be above 1.2V. Figure 6 shows an example of
this where OUT1 is set to 1V. To set the output voltage to
less than 1.2V, connect a resistor from FB1 to OUT1 (R1),
and from FB1 to OUT2 (R2). Select values of R1 and R2
such that current flowing through R1 and R2 is about
100μA and following equation is satisfied:
Each output is capable of continuously sourcing up to
750mA of current as long as the following condition is
met:
Inductor Value
A 3.3μH to 6.8μH inductor with a saturation current of
800mA (min) is recommended for most applications.
For best efficiency, the inductor
’
s DC resistance should
be less than 100m
, and saturation current should be
greater than 1A. See Table 2 for recommended induc-
tors and manufacturers.
V
I
V
I
V
A
OUT
OUT
OUT
OUT
IN
1
1
2
2
1 05
≤
.
×
+
×
R
R
V
V
OUT
1
OUT
1
21 2
1 2
.
2
=
.
R
R
V
a
b
OUT
1.
_
_
=
×
1
Dual, 180° Out-of-Phase, 1.4MHz, 750mA Step-
Down Regulator with POR and RSI/PFO
14
______________________________________________________________________________________
Figure 2. Timing Diagram
V
OUT
T
D
RSI
~1V PKMAX
V
IN
PFO
4.04V
3.94V
T
RESET
= 1
μ
s MIN
T
D
POR
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1970EEE | Fixed-Point Digital Signal Processor 532-FCBGA |
| MAX1971 | Fixed-Point Digital Signal Processor 532-FCBGA |
| MAX1972 | Dual, 180∑ Out-of-Phase, 1.4MHz, 750mA Step- Down Regulator with POR and RSI/PFO |
| MAX1972EEE | Fixed-Point Digital Signal Processor 532-FCBGA |
| MAX1973 | Smallest 1A, 1.4MHz Step-Down Regulators |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX19700ETM | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19700ETM+ | 功能描述:ADC / DAC多通道 7.5Msps CODEC/AFE 1.8/2.7-3.3V RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19700ETM+T | 功能描述:ADC / DAC多通道 7.5Msps CODEC/AFE 1.8/2.7-3.3V RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19700ETM-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| MAX19700EVCMOD2 | 功能描述:ADC / DAC多通道 Evaluation Kit/Evaluation System for the MAX19700 RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
发布紧急采购，3分钟左右您将得到回复。