- 您现在的位置：买卖IC网 > Datasheet目录471 > MAX19995EVKIT# (Maxim Integrated)EVALUATION KIT FOR MAX19995 Datasheet资料下载
参数资料
| 型号： | MAX19995EVKIT# |
| 厂商： | Maxim Integrated |
| 文件页数： | 20/23页 |
| 文件大小： | 0K |
| 描述： | EVALUATION KIT FOR MAX19995 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 混频器，降频 |
| 频率： | 1.7GHz ~ 2.2GHz |
| 适用于相关产品： | MAX19996A |
Dual, SiGe, High-Linearity, 1700MHz to 2200MHz
Downconversion Mixer with LO Buffer/Switch
Applications Information
Input and Output Matching
The RF and LO inputs are internally matched to 50 Ω .
No matching components are required. The RF port
input return loss is typically better than 16.5dB over the
RF frequency range of 1700MHz to 2200MHz and
return loss at the LO ports is typically better than 15dB
over the entire LO range. RF and LO inputs require only
DC-blocking capacitors for interfacing.
The IF output impedance is 200 Ω (differential). For
evaluation, an external low-loss 4:1 (impedance ratio)
balun transforms this impedance to a 50 Ω single-ended
output (see the Typical Application Circuit).
Reduced-Power Mode
Each channel of the MAX19995A has two pins
(LO_ADJ_ _, IF_ _SET) that allow external resistors to
set the internal bias currents. Nominal values for these
resistors are given in Table 1. Larger value resistors
can be used to reduce power dissipation at the
expense of some performance loss. If ±1% resistors
are not readily available, substitute with ±5% resistors.
Significant reductions in power consumption can also
be realized by operating the mixer with an optional sup-
ply voltage of 3.3V. Doing so reduces the overall power
consumption by up to 54%. See the 3.3V Supply AC
Electrical Characteristics table and the relevant 3.3V
curves in the Typical Operating Characteristics section.
IND_EXT_ Inductors
For applications requiring optimum RF-to-IF and LO-to-
IF isolation, connect low-ESR inductors from IND_EXT_
(pins 15 and 31) to ground. When improved isolation is
not required, connect IND_EXT_ to ground using 0 Ω
resistance. See the Typical Operating Characteristics to
evaluate the isolation vs. inductor value tradeoff.
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. Keep RF signal lines as short as
possible to reduce losses, radiation, and inductance.
The load impedance presented to the mixer must be so
that any capacitance from both IF- and IF+ to ground
does not exceed several picofarads. For the best per-
formance, route the ground pin traces directly to the
exposed pad under the package. The PCB exposed
pad MUST be connected to the ground plane of the
PCB. It is suggested that multiple vias be used to con-
nect this pad to the lower-level ground planes. This
method provides a good RF/thermal-conduction path
for the device. Solder the exposed pad on the bottom
of the device package to the PCB. The MAX19995A
evaluation kit can be used as a reference for board lay-
out. Gerber files are available upon request at
www.maxim-ic.com .
Power-Supply Bypassing
Proper voltage-supply bypassing is essential for high-
frequency circuit stability. Bypass each V CC pin and
TAPMAIN/TAPDIV with the capacitors shown in the
Typical Application Circuit (see Table 1 for component
values). Place the TAPMAIN/TAPDIV bypass capacitors
to ground within 100 mils of the pin.
Exposed Pad RF/Thermal Considerations
The exposed pad (EP) of the MAX19995A’s 36-pin thin
QFN-EP package provides a low thermal-resistance
path to the die. It is important that the PCB on which the
MAX19995A is mounted be designed to conduct heat
from the EP. In addition, provide the EP with a low-
inductance path to electrical ground. The EP MUST be
soldered to a ground plane on the PCB, either directly
or through an array of plated via holes.
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX19996AEVKIT# | EVALUATION KIT FOR MAX19996A |
| MAX19996ETP+T | IC MIXER DOWNCONV 20-TQFN-EP |
| MAX19997AETX+T | IC DOWNCONVERTER 2CH 36TQFN |
| MAX19998ETP+ | IC MIXER DOWNCONVERSION 20TQFN |
| MAX19999ETX+T | IC DOWNCONVERTER 2CH 36TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX19995EVKIT# | 功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX19996AETP+ | 功能描述:上下转换器 High-Gain 2GHz to 3.9GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX19996AETP+T | 功能描述:上下转换器 High-Gain 2GHz to 3.9GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX19996AEVKIT# | 功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX19996ETP+ | 功能描述:上下转换器 High-Gain 2GHz to 3.9GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
发布紧急采购，3分钟左右您将得到回复。