- 您现在的位置：买卖IC网 > PDF目录21941 > MAX2361ETM+T (Maxim Integrated)IC TRANSMITTER QUAD 48TQFN-EP PDF资料下载
参数资料
| 型号： | MAX2361ETM+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 13/29页 |
| 文件大小： | 460K |
| 描述： | IC TRANSMITTER QUAD 48TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 800MHz ~ 2.2GHz |
| 功率 - 输出： | 9dBm |
| 电流 - 传输： | 146mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 2.7 V ~ 3.3 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Complete Dual-Band
Quadrature Transmitters
______________________________________________________________________________________ 13
Programmable Registers
The MAX2361/MAX2363/MAX2365 include eight pro-
grammable registers consisting of four divide registers,
a configuration register, an operational control register,
a current control register, and a test register. Each reg-
ister consists of 24 bits. The 4 least significant bits
(LSBs) are the registers address. The 20 most signifi-
cant bits (MSBs) are used for register data. All registers
contain some don't care bits. These can be either a
0 or a 1 and will not affect operation (Figure 1). Data
is shifted in MSB first, followed by the 4-bit address.
When CS is low, the clock is active and data is shifted
with the rising edge of the clock. When CS transitions to
high, the shift register is latched into the register select-
ed by the contents of the address bits. Power-up
defaults for the eight registers are shown in Table 1.
The dividers and control registers are programmed
from the SPI/QSPI/MICROWIRE-compatible serial port.
The RFM register sets the main frequency divide ratio
for the RF PLL. The RFR register sets the reference fre-
quency divide ratio. The RF VCO frequency can be
determined by the following:
RF VCO frequency = f
REF
(RFM / RFR)
IFM and IFR registers are similar:
IF VCO frequency = f
REF
(IFM / IFR)
where f
REF
is the external reference frequency.
The operational control register (OPCTRL) controls the
state of the MAX2361/MAX2363/MAX2365. See Table 2
for the function of each bit.
The configuration register (CONFIG) sets the configura-
tion for the RF/IF PLL and the baseband I/Q input lev-
els. See Table 3 for a description of each bit.
The current control register modifies the bias current to
accommodate different operation modes. In the high-
power mode, MPL = 1 sets the bias current and con-
version gain to deliver a minimum of +8dBm output
power from the PA drivers. In the low-power mode,
MPL = 0 sets the bias current and conversion gain to
deliver a minimum of +5dBm output power from the PA
drivers. I_MULT sets the current multiplication factor for
the PA driver stages according to Table 5. THROT-
TLE_BACK sets the rate of bias current changes when
the output power changes according to Table 6. For
example, when THROTTLE_BACK = 011 (default), the
PA driver bias current reduces by 1dBmA for every
1dB reduction in output power. THROTTLE_BACK =
000 setting gives a more aggressive current reduction
(1.3dBmA/dB power) at the expense of linearity.
THROTTLE_BACK setting does not affect the bias cur-
rent at maximum power level.
The test register has to be 100hex for normal operation.
The best way to ensure this is to program the test regis-
er to 100hex.
Power Management
Bias control is distributed among several functional
sections and can be controlled to accommodate many
different power-down modes as shown in Table 8.
The serial interface remains active during shutdown.
Setting SHDN_BIT = 0 or SHDN = GND powers down
the device. In either case, PLL programming and regis-
ter information is retained.
Signal Flow Control
Table 9 shows an example of key registers for triple-
mode operation, assuming half-band PCS and IF fre-
quencies of 228.6MHz/263.6MHz.
Applications Information
The MAX2361 is designed for use in dual-band, triple-
mode systems. It is recommended for triple-mode hand-
sets (Figure 2). The MAX2363 is designed for use in
CDMA PCS handset or W-CDMA systems (Figure 3).
The MAX2365 is designed for use in dual-mode cellular
systems (Figure 4).
Table 1. Register Power-Up Default States
TEST
0111
b
100 hex
Test-mode control
CONFIG
OPCTRL
IFR
0101
b
0100
b
0011
b
0492 dec
090F hex
D03F hex
IFM
RFR
RFM
REGISTER
0010
b
0001
b
0000
b
ADDRESS
DEFAULT
32214 dec
656 dec
6519 dec
Configuration and setup control
Operational control settings
IF R divider count
IF M divider count
RF R divider count
RF M divider count
FUNCTION
I
CC
CTRL
0110
b
0038 hex
Current multiplication factor, PLL band
相关PDF资料 |
PDF描述 |
|---|---|
| B-8-1 | CORD PATCH BANANA PLUG 8" BROWN |
| ATS177-PL-A-A | IC HALL SENSOR LATCH 25MA SIP-3L |
| MAX2361ETM+ | IC TRANSMITTER QUAD 48TQFN-EP |
| MAX2365ETM+ | IC TRANSMITTER QUAD 48TQFN-EP |
| CVHD-950-122.880 | VCXO CMOS 122.880 MHZ 3.3V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2361ETM-TB4A | 功能描述:射频发射器 RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
| MAX2361EVKIT | 功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX2361EVKIT# | 功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX2362ECM | 功能描述:射频发射器 RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
| MAX2362ECM-T | 功能描述:射频发射器 RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。