- 您现在的位置：买卖IC网 > PDF目录18737 > MAX2831ETM+T (Maxim Integrated)IC TXRX 2.4GHZ-2.5GHZ 48TQFN PDF资料下载
参数资料
| 型号： | MAX2831ETM+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 22/34页 |
| 文件大小： | 0K |
| 描述： | IC TXRX 2.4GHZ-2.5GHZ 48TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 2.4GHz ~ 2.5GHz |
| 数据传输率 - 最大： | 54Mbps |
| 调制或协议： | 802.11b/g |
| 应用： | WLAN |
| 功率 - 输出： | 18.5dBm |
| 灵敏度： | -76dBm |
| 电源电压： | 2.7 V ~ 3.6 V |
| 电流 - 接收： | 62mA |
| 电流 - 传输： | 209mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
2.4GHz to 2.5GHz 802.11g/b
RF Transceivers with Integrated PA
Baseband Variable-Gain Amplifier
The receiver baseband variable-gain amplifiers provide
62dB of gain control range programmable in 2dB steps.
The VGA gain can be serially programmed through the
SPI interface by setting bits D4:D0 in Register 11 (A3:A0
= 1011) or programmed in parallel through the digital
logic gain-control pins, B5 (pin 14), B4 (pin 34), B3 (pin
8), B2 (pin 11), and B1 (pin 23). Set bit D12 = 1 in
Register 8 (A3:A0 = 1000) to enable serial programming
through the serial interface or set bit D12 = 0 to enable
parallel programming through the external logic pins.
See Table 2 for the gain-step value and Table 3 for
baseband VGA gain-control settings.
Receiver Baseband Lowpass Filter
The receiver integrates lowpass filters that provide an
upper -3dB corner frequency of 8.5MHz (nominal mode)
with 50dB of attenuation at 20MHz, and 45ns of group
delay ripple in the passband (10kHz to 8.5MHz). The
upper -3dB corner frequency is tightly controlled on-chip
and does not require user adjustment. However, provi-
sions are made to allow fine tuning of the upper -3dB cor-
Baseband Highpass Filter
and DC Offset Correction
The receiver implements programmable AC and near-
DC coupling of I/Q baseband signals. Temporary AC-
coupling is used to quickly remove LO leakage and
other DC offsets that could saturate the receiver out-
puts. When DC offsets have settled, near DC-coupling
is enabled to avoid attenuation of the received signal.
AC-coupling is set (-3dB highpass corner frequency of
600kHz) when a logic-high is applied to RXHP (pin 40).
Near DC-coupling is set (-3dB highpass corner fre-
quency of 100Hz nominal) when a logic-low is applied
to RXHP. Bits D13:D12 in Register 7 (A3:A0 = 0111)
allow the near DC-coupling -3B highpass corner fre-
quency to be set to 100Hz (D13:D12 = 00), 4kHz
(D13:D12 = X1), or 30kHz (D13:D12 = 10). See Table 6.
Table 4. Receiver LPF Coarse -3dB
Corner Frequency Settings in Register
(A3:A0 = 1000)
ner frequency. In addition, coarse frequency tuning
allows the -3dB corner frequency to be set to 7.5MHz
(11b mode), 8.5MHz (11g mode), 15MHz (turbo 1 mode),
and 18MHz (turbo 2 mode) by programming bits D1:D0
in Register 8 (A3:A0 = 1000). See Table 4. The coarse
corner frequency can be fine-tuned approximately ±10%
in 5% steps by programming bits D2:D0 in Register 7
BITS (D1:D0)
00
01
10
11
-3dB CORNER
FREQUENCY (MHz)
7.5
8.5
15
18
MODE
11b
11g
Turbo 1
Turbo 2
(A3:A0 = 0111). See Table 5 for receiver LPF fine -3dB
corner frequency adjustment.
Table 2. Receiver Baseband VGA Gain-
Step Value (Pins B5:B1 or Register D4:D0,
Table 5. Receiver LPF Fine -3dB Corner
Frequency Adjustment in Register
(A3:A0 = 0111)
A3:A0 = 1011)
PIN/BIT
B1/D0
B2/D1
B3/D2
B4/D3
B5/D4
GAIN STEP (dB)
2
4
8
16
32
BITS (D2:D0)
000
001
010
011
100
% ADJUSTMENT RELATIVE TO
COARSE SETTING
90
95
100
105
110
Table 3. Baseband VGA Gain-Control
Settings in Receiver Gain-Control Register
(Pin B5:B1 or Register D4:D0, A3:A0 = 1011)
B5:B1 OR D4:D0 GAIN
Table 6. Receiver Highpass Filter -3dB
Corner Frequency Programming
A3:A0 = 0111, -3dB HIGHPASS CORNER
RXHP
D13:D12 FREQUENCY (Hz)
11111
11110
11101
:
00000
Max
Max - 2dB
Max - 4dB
:
Min
1
0
0
0
X = Don’t care.
XX
00
X1
10
600k
100 (recommended)
4k
30k
22
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| X-10GQ | SWITCH BASIC PNL MT 10A SOLDER |
| B82802A0030A220 | TRANSFORMER FLYBACK 36-60V SMD |
| MAX7030LATJ+T | IC ASK TXRX 315MHZ 32-TQFN |
| CCHD-950-20-104.000 | OSC CMOS 104.000 MHZ 3.3V SMD |
| DZ-10GV2-1B | SWITCH BASIC DPDT 10A 270GF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2831EVKIT+ | 功能描述:WiFi/802.11开发工具 MAX2831 Eval Kit RoHS:否 制造商:Roving Networks 产品:Evaluation Boards 工具用于评估:RN-171 支持协议:802.11 b/g 频率:2.4 GHz 接口类型:UART 工作电源电压:2 V to 16 V |
| MAX2832ETM+ | 制造商:Maxim Integrated Products 功能描述:2.4GHZ TO 2.5GHZ, 802.11G RF TRANSCEIVER 制造商:Maxim Integrated Products 功能描述:IC+MAX2832ETM+ - Rail/Tube |
| MAX2832ETM+CFK | 制造商:Maxim Integrated Products 功能描述:2.4GHZ TO 2.5GHZ, 802.11G RF TRANSCEIVERS WITH INTEGRATED PA - Rail/Tube |
| MAX2832ETM+T | 制造商:Maxim Integrated Products 功能描述:2.4GHZ TO 2.5GHZ, 802.11G RF TRANSCEIVER 制造商:Maxim Integrated Products 功能描述:2.4GHZ TO 2.5GHZ, 802.11G RF TRANSCEIVERS WITH INTEGRATED PA - Tape and Reel |
| MAX2832ETM+TCFK | 制造商:Maxim Integrated Products 功能描述:2.4GHZ TO 2.5GHZ, 802.11G RF TRANSCEIVERS WITH INTEGRATED PA - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。