- 您现在的位置：买卖IC网 > PDF目录18731 > MAX2851ITK+T (Maxim Integrated)TRANSMITTER MIMO 5GHZ 5CH 68TQFN PDF资料下载
参数资料
| 型号： | MAX2851ITK+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 23/37页 |
| 文件大小： | 0K |
| 描述： | TRANSMITTER MIMO 5GHZ 5CH 68TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 4.9GHz ~ 5.9GHz |
| 数据传输率 - 最大： | 54Mbps |
| 调制或协议： | * |
| 应用： | * |
| 功率 - 输出： | -3dBm |
| 电源电压： | 2.7 V ~ 3.6 V |
| 电流 - 接收： | * |
| 电流 - 传输： | * |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -25°C ~ 85°C |
| 封装/外壳： | 68-TQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
5GHz, 5-Channel MIMO Receiver
Table 1. Operating Modes
MODE CONTROL
LOGIC INPUTS
CIRCUIT BLOCK STATES
MODE
SHUTDOWN
CLOCKOUT
STANDBY
Rx
Tx
Tx CALIBRATION
RF LOOPBACK
BASEBAND
LOOPBACK
ENABLE
PIN
0
1
1
1
1
1
1
1
SPI MAIN
ADDRESS 0,
D[4:2]
XXX
000
001
010
011
100
101
11X
Rx PATH
Off
Off
Off
On
Off
Off
On (except LNA)
On (except RXRF)
Tx PATH
(NOTE 1)
Off
Off
Off
Off
On
On
On
Off
LO PATH
Off
Off
On
On
On
On
On
On
CLKOUT
(NOTES 2, 3)
Off
On
On
On
On
On
On
On
CALIBRATION
SECTIONS ON
None
None
None
None
None
AM detector + Rx5
I/Q buffers
RF loopback
Tx baseband buffer
Note 1: PA_BIAS pin can be kept active in nontransmit mode(s) by SPI programming.
Note 2: CLKOUT signal is active independent of SPI, and is only dependent on the ENABLE pin.
Note 3: CLKOUT2 signal can be enabled/disabled through SPI in all operating modes except shutdown mode.
Detailed Description
Modes of Operation
The MAX2851 modes of operation are shutdown, clock-
out, standby, receive, transmit, transmitter calibration,
RF loopback, and baseband loopback. See Table 1 for
a summary of the modes of operation. The logic input pin
ENABLE (pin 68) and SPI Main address 0 D[4:2] control
the various modes.
Shutdown Mode
The MAX2851 features a low-power shutdown mode. All
circuit blocks are powered down, except the 4-wire serial
bus and its internal programmable registers.
Clockout Mode
In clockout mode, only the crystal oscillator signal is
active at the CLKOUT pin. The rest of the transceiver is
powered down.
Standby Mode
In standby mode, PLL, VCO, and LO generation are on.
Tx or Rx modes can be quickly enabled from this mode.
Other blocks can be selectively enabled in this mode
Receive (Rx) Mode
In receive mode, all Rx circuit blocks are powered on
and active. The antenna signal is applied; RF is down-
converted, filtered, and buffered at the RXBB I and Q
outputs.
Transmit (Tx) Mode
In transmit mode, all Tx circuit blocks are powered on
and active. The external PA can be powered on through
the PA_BIAS pin after a programmable delay.
Transmit Calibration Mode
In transmit calibration mode, all Tx circuit blocks are
powered on and active. The AM detector and receiver
I/Q channel buffers are also on. Output signals are
routed to RXBB I and Q outputs.
The AM detector multiplies the Tx RF output signal with
itself. The self-mixing product of the wanted sideband
becomes DC voltage and is filtered on-chip. The mixing
product between wanted sideband and the carrier leak-
age forms Ftone at the Rx baseband output. The mixing
product between the wanted sideband and the unwant-
ed sideband forms 2Ftone at the Rx baseband output.
As the Tx RF output is self-mixed at the AM detector,
the AM detector output responds differently to different
gain settings and power levels. When the Tx RF output
power changes by 1dB through Tx gain control, the AM
detector output changes by 2dB as both the wanted
sideband and carrier leakage (or unwanted sideband)
change by 1dB. When Tx RF output carrier leakage (or
unwanted sideband) changes by 1dB while the wanted
sideband output power is constant, the AM detector out-
put changes by 1dB only.
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| MTCBA-E-U | MODEM GPRS QUAD BUNDLE USB |
| MTCBA-E-EU | MODEM GPRS QUAD EU BUNDLE RS-232 |
| MTCBA-E | MODEM GPRS QUAD DC POWER RS-232 |
| LP0805A1842ASTR | LOW PASS FILTER 1842MHZ 0805 SMD |
| MAX2821ETM+ | IC TXRX 802.11B 2.4GHZ 48-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2852ITK+ | 功能描述:射频接收器 5Ghz Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX2852ITK+T | 功能描述:射频接收器 5Ghz Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX2870ETJ+ | 功能描述:锁相环 - PLL PLL/VCO RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| MAX2870ETJ+T | 功能描述:锁相环 - PLL PLL/VCO RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| MAX2870EVKIT# | 功能描述:射频开发工具 MAX2870 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。