- 您现在的位置：买卖IC网 > PDF目录1842 > MAX34440ETL+T (Maxim Integrated Products)IC PS MANAGER PMBUS 6CH 40TQFN PDF资料下载
参数资料
| 型号： | MAX34440ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/43页 |
| 文件大小： | 0K |
| 描述： | IC PS MANAGER PMBUS 6CH 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 基站网络线路卡，服务器 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 2.5mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 带卷 (TR) |
| 其它名称： | 90-34440+TTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
MAX34440
PMBus 6-Channel Power-Supply Manager
STORE_DEFAULT_ALL (11h)
The STORE_DEFAULT_ALL command instructs the device to transfer the device configuration information to the internal
flash memory array. Not all information is stored. Only configuration data is stored, not any status, or operational data.
If an error occurs during the transfer, ALERT asserts if enabled and the CML bit in STATUS_BYTE and STATUS_WORD
is set to 1. No bits are set in STATUS_CML. It is NOT recommended to use the STORE_DEFAULT_ALL command
while the device is operating power supplies. The device is unresponsive to PMBus commands and does not moni-
tor power supplies while transferring the configuration. After this command is sent, another commmand should not be
sent for at least 250ms. This command is write-only. There is no data byte for this command.
USER NOTE: V DD must be above 2.9V for the device to perform the STORE_DEFAULT_ALL command.
RESTORE_DEFAULT_ALL (12h)
The RESTORE_DEFAULT_ALL command transfers the default configuration information from the internal flash memory
array to the user memory registers in the device. The RESTORE_DEFAULT_ALL command should only be executed
when the device is not operating the power supplies. Upon a device reset, this command is automatically executed by
the device without PMBus action required. After this command is sent, another commmand should not be sent for at
least 250ms. This command is write-only. There is no data byte for this command.
CAPABILITY (19h)
The CAPABILITY command is used to determine some key capabilities of the device. The CAPABILITY command is
read-only. The message content is described in the Table 12.
Table 12. CAPABILITY Command Byte
BIT
7
6:5
4
3:0
DESCRIPTION
Packet-Error Checking
PMBus Speed
ALERT
Reserved
MEANING
0 = PEC not supported.
00 = Maximum supported bus speed is 100kHz.
1 = Device supports an ALERT output (if ALERT is enabled in MFR_MODE).
0 = Device does not support ALERT output (ALERT is disabled in MFR_MODE).
Always returns 0000.
VOUT_MODE (20h)
The VOUT_MODE command is used to report the data format of the device. The device uses the DIRECT format for all
the voltage-related commands. The value returned is 40h, indicating DIRECT data format. This command is read-only.
If a host attempts to write this command, the CML status bit is asserted. See Table 3 for the m, b, and R values for the
various commands.
VOUT_MARGIN_HIGH (25h)
The VOUT_MARGIN_HIGH command loads the device with the voltage to which the power-supply output is to be
changed when the OPERATION command is set to margin high. If the power supply is already operating at margin
high, changing VOUT_MARGIN_HIGH has no effect on the output voltage. The device only adjusts the power supply to
the new VOUT_MARGIN_HIGH voltage after receiving a new margin high OPERATION command. The 2 data bytes are
in DIRECT format. If the device cannot successfully close-loop margin the power supply, the device keeps attempting
to margin the supply and does the following:
1) Sets the NONE OF THE ABOVE bit in STATUS_BYTE.
2) Sets the NONE OF THE ABOVE and MFR bits in STATUS_WORD.
3) Sets the MARGIN_FAULT bit in STATUS_MFR_SPECIFIC.
4) Notifies the host through ALERT assertion (if enabled in MFR_MODE).
26
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX34441ETL+T | IC PS MANAGER PMBUS 5CH 40TQFN |
| MAX3600CTL+ | IC LASER DVR PROJECTOR 40TQFN |
| MAX3643ETG+T | IC LASR DRVR 2.5GBPS 3.6V 24TQFN |
| MAX3646ETG+T | IC LSR DRVR 622MBPS 3.63V 24TQFN |
| MAX3656ETG+ | IC LASR DRVR 2.5GBPS 3.6V 24TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX34441ETL+ | 功能描述:监控电路 PMBus 6Ch Power Supply Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX34441ETL+T | 功能描述:监控电路 PMBus 6Ch Power Supply Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX34441EVKIT# | 功能描述:电源管理IC开发工具 MAX34441 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX34446ETL+ | 功能描述:监控电路 PMBus Power Supply Data Logger RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX34446ETL+T | 功能描述:监控电路 PMBus Power Supply Data Logger RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。