- 您现在的位置：买卖IC网 > PDF目录18709 > MAX3580EVKIT+ (Maxim Integrated)KIT EVAL FOR MAX3580 TV TUNER PDF资料下载
参数资料
| 型号： | MAX3580EVKIT+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX3580 TV TUNER |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 调谐器 |
| 频率： | 170MHz ~ 230MHz，470MHz ~ 878MHz |
| 适用于相关产品： | MAX3580 |
| 已供物品： | 板 |
MAX3580
Direct-Conversion TV Tuner
18
______________________________________________________________________________________
Applications Information
Band Selection
The MAX3580 is designed to be suitable for operation
in the 170MHz to 230MHz VHF-III band and in the
470MHz to 878MHz UHF band.
RF Inputs
A switch selects either RFIN or RFIN2 as the input to the
single-ended broadband matched LNA. This switch is
programmed through the RFS bit (bit 5) of register 0x05.
The LNA provides a continuous gain control range of
typically 50dB before the signal is downconverted.
For optimal matching above 600MHz, add a 5nH to
6nH inductor in series with a capacitor at either of the
RF input. Application Note:
Front End Diplexer Filter for
MAX3580 is available, detailing the implementation of a
UHF and VHF simple diplexer. This simple diplexer
improves strong-signal-handling capabilities of the
MAX3580.
DC-Offset Cancellation
The MAX3580 features an on-chip fast-settling, DC-off-
set cancellation circuitry that requires no off-chip com-
ponents. Note that the offset correction circuit is not
enabled when the device is powered up. To enable the
offset correction circuit, program the DC-Offset Control
Register to the recommended default setting.
When active, the offset correction circuit creates a high-
pass characteristic in the signal path with a typical cor-
ner frequency of 200Hz, and the residual DC offset can
be as high as ±70mV.
Gain Control
The MAX3580 features two VGA circuits that can be
used to achieve the optimum SNR. The two circuits can
be driven independently by the baseband controller,
which allows balancing the gain based on SNR measure-
ments in the digital demodulator. If only one gain control
voltage can be provided by the digital demodulator, see
Figure 1. See the
Baseband Power Detector section. In
this operation mode, the baseband gain is set by an
amplitude detector in the digital demodulator.
Baseband Power Detector
Maxim recommends disabling this feature. See expla-
nation in the
Shutdown Control (Register Address 0x08)
section and Table 2 (address 0x08, bit D5). For single-
loop AGC control, see Figure 1.
Synthesizer Loop Filters
A second-order lowpass loop filter is used to connect
the PLL to the RF local oscillator. A loop filter bandwidth
of 30kHz is optimal for fractional PLL spurs and integrat-
ed LO phase noise. Refer to the EV kit data sheet for the
recommended loop-filter component values.
Crystal-Oscillator Interface
The MAX3580 reference oscillator circuitry can be used
either as a high-impedance reference input driven by
an external source, or be configured as a crystal oscil-
lator. In the latter case, the resulting frequency can be
used to drive the digital demodulator chip through the
buffered reference output of the MAX3580. When using
an external reference oscillator, drive the XB input
through an AC-coupling capacitor with amplitude of
approximately 1.5VP-P, and leave XE unconnected.
Note that the phase noise of the external reference
needs to exceed -140dBc/Hz at offsets of 1kHz to
100kHz. When connecting directly to a crystal, see the
Typical Application Circuit for the required topology.
For particular capacitor values, possible changes to
accommodate for different crystal frequencies, crystal
load-capacitance requirements, and crystal power-dis-
sipation requirements, refer to the EV kit data sheet.
相关PDF资料 |
PDF描述 |
|---|---|
| GLAA01E7B | SWTCH WOBBLE/COIL SPRING SPDT |
| MAX11008EVKIT+ | KIT EVAL FOR MAX11008 BIAS CTLR |
| MAX1471EVSYS-315 | EVAL KIT FOR MAX1471 315MHZ |
| MAX1471EVSYS-433 | EVAL KIT FOR MAX1471 433MHZ |
| MDEV-LICAL-MS | DEV SYSTEM MS SERIES 418MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3580EVKIT+ | 功能描述:射频开发工具 MAX3580 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX358C/D | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX358C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX358CJE | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX358CPE | 功能描述:多路器开关 IC 8:1 Fault-Protected Analog MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。