- 您现在的位置：买卖IC网 > PDF目录18709 > MAX3580EVKIT+ (Maxim Integrated)KIT EVAL FOR MAX3580 TV TUNER PDF资料下载
参数资料
| 型号： | MAX3580EVKIT+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX3580 TV TUNER |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 调谐器 |
| 频率： | 170MHz ~ 230MHz，470MHz ~ 878MHz |
| 适用于相关产品： | MAX3580 |
| 已供物品： | 板 |
MAX3580
Direct-Conversion TV Tuner
14
______________________________________________________________________________________
Shutdown Control (Register Address 0x08)
SHDN_BG: Main Bandgap
0 = Enabled
1 = Disabled
The main bandgap can and will be shut down
once all other blocks are shut down (i.e., all bits in this
shutdown register and bits VCO_ in the VCO
Control Register and bits DC_MO_ in the DC
Offset Control Register are shut down).
SHDN_PD: Baseband Power Detector
For factory use only.
Set to 1 at all times.
SHDN_RF: RF LNA/VGA:
0 = Enabled
1 = Disabled
SHDN_MIX: I/Q Mixer and LO Drivers
0 = Enabled
1 = Disabled
SHDN_BB: Baseband Filters and VGA
0 = Enabled
1 = Disabled
SHDN_SYN: Fractional PLL
0 = Enabled
1 = Disabled
SHDN_REF: Controls the Crystal Oscillator Buffered
Output
0 = Enabled
1 = Disabled
The XTAL oscillator activation results from the
SHDN_SYN, SHDN_REF bits: If either one is on,
the XTAL oscillator runs. The XTAL oscillator is
shut down only if both bits are off.
VCO Control (Register Address 0x09)
VCO<1:0>: Selects 1 of 3 VCO Bands. 00 turns off
VCO block completely.
BS<2:0>: Selects 1 of 8 VCO Sub-Bands
VAS: VCO Band Autoselect
0 = VCO band select controlled by bits VCO<1:0>
1 = Controlled by autotuner
ADL: VCO ADC Latch Enable Bit
1 = Latches ADC value
0 = Default
ADE: Enable VCO Tune Voltage DAC Read
1 = Enables ADC read
0 = Default
Baseband Control (Register Address 0x0A)
PD_TH<2:0>: Detection Threshold for Baseband
Power Detector
BB_BW<3:0>: Baseband Filter Bandwidth. Optimum
values for 7MHz and 8MHz wide RF channels can
be taken from the ROM table.
DC Offset Control (Register Address 0x0B)
DC_TH<1:0>: DC Offset Correction Thresholds.
Keeps output within:
00 = Output within ±0.55V of balanced state
11 = Output within ±0.75V of balanced state
DC_SP<1:0>: DC Offset Correction Speed (or Highpass
Corner Frequency).
11 = Fast (~500Hz)
01 = Slow (~20Hz)
00 = Off/hold DAC values
DC_MO<1:0>: Mode of Operation
00 = Off
10/01 = Sets I/Q channel DACs direct from register
11 = Normal operation
DC_DAC<8>: MSB for DC Offset DAC
BB_BIA: Baseband Filter Op-Amp Bias Settings
0 = Low
1 = High
*
Not production tested.
相关PDF资料 |
PDF描述 |
|---|---|
| GLAA01E7B | SWTCH WOBBLE/COIL SPRING SPDT |
| MAX11008EVKIT+ | KIT EVAL FOR MAX11008 BIAS CTLR |
| MAX1471EVSYS-315 | EVAL KIT FOR MAX1471 315MHZ |
| MAX1471EVSYS-433 | EVAL KIT FOR MAX1471 433MHZ |
| MDEV-LICAL-MS | DEV SYSTEM MS SERIES 418MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3580EVKIT+ | 功能描述:射频开发工具 MAX3580 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX358C/D | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX358C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX358CJE | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX358CPE | 功能描述:多路器开关 IC 8:1 Fault-Protected Analog MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。