- 您现在的位置：买卖IC网 > PDF目录5331 > MAX366CPA+ (Maxim Integrated Products)IC CIRCUIT PROT SIGNAL-LINE 8DIP PDF资料下载
参数资料
| 型号： | MAX366CPA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC CIRCUIT PROT SIGNAL-LINE 8DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 电压 - 箝位： | ±40V |
| 技术： | 混合技术 |
| 功率（瓦特）： | 727mW |
| 电路数： | 3 |
| 应用： | 通用 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
Signal-Line Circuit Protectors
__High-Voltage Surge Suppression
These devices are not high-voltage arresters, nor are they
substitutes for surge suppressers. In systems that use
these forms of protection, however, the MAX366/MAX367
+5V
can fill a vital gap. Figure 7 shows a typical circuit.
Although the surge suppressers are extremely fast shunt
MAX366
V+
8
elements, they have very soft current knees. Their clamp
voltage must be chosen well above the normal signal
levels, because they have excessive leakage currents as
the knee is approached. This current can interfere with
1
2
IN1
IN2
OUT1
OUT2
7
6
normal operation when signal levels are low or imped-
ances are high. If the clamp voltage is too high, however,
3
IN3
OUT3
5
OP AMP
the input can be damaged.
Using a MAX366/MAX367 after the surge suppresser
allows the surge-suppresser voltage to be set above
the supply voltage (but within the overvoltage limits),
dramatically reducing the effects of leakage (Figure 7).
During a surge, the surge suppresser clamps the input
voltage to roughly ±10V. This protects the
MAX366/MAX367, but the MAX366/MAX367 still dis-
SURGE SUPPRESSERS
(+10V)
4
V-
-5V
connect the signal from the op amp well within the ±5V
supply.
_________________Pin Configurations
Figure 7. Surge-Suppression Circuit
___________________Chip Topography
IN1
TOP VIEW
IN1
1
18 V+
V+
IN2 2
17 OUT1
IN1 1
IN2 2
8 V+
7 OUT1
IN3 3
IN4 4
16 OUT2
15 OUT3
IN2
OUT1
0.112"
IN3 3
V- 4
6 OUT2
5 OUT3
IN5 5
IN6 6
14 OUT4
13 OUT5
(2.84mm)
MAX366
DIP/SO
IN7 7
IN8 8
12 OUT6
11 OUT7
IN3
OUT2
V- 9
10 OUT8
MAX367
DIP/SO
V-
0.085"
(2.16mm)
TRANSISTOR COUNT: 21
SUBSTRATE CONNECTED TO V+
OUT3
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| EL8403IU | IC OP AMP 500MHZ R-R 16-QSOP |
| 7100.1114.13 | FUSE 800MA 250V T-LAG 19MM PCB |
| B2050CCLRP | BATTRAX SLIC DUAL NEG 500A DO214 |
| RGH2012-2E-P-512-B | RES 5.1K OHM .1% 1/4W 0805 SMD |
| ADG465BRTZ-REEL7 | IC CHANNEL PROTECTOR SGL SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX366CPA+ | 功能描述:隔离器接口集成电路 Signal Line Circuit Protector RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| MAX366CSA | 功能描述:TVS二极管阵列 RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
| MAX366CSA+ | 功能描述:隔离器接口集成电路 Signal Line Circuit Protector RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| MAX366CSA+T | 功能描述:隔离器接口集成电路 Signal Line Circuit Protector RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| MAX366CSA-T | 功能描述:TVS二极管阵列 RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
发布紧急采购，3分钟左右您将得到回复。