- 您现在的位置：买卖IC网 > PDF目录2157 > MAX3798ETJ+T (Maxim Integrated Products)IC LIMITING AMP/VCSEL DVR 32TQFN PDF资料下载
参数资料
| 型号： | MAX3798ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/35页 |
| 文件大小： | 0K |
| 描述： | IC LIMITING AMP/VCSEL DVR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 放大器类型： | 限制 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 电流 - 电源： | 97mA |
| 电压 - 电源，单路/双路(±)： | 2.85 V ~ 3.63 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
controls the output eye-crossing adjustment. A status
indicator bit (TXED) monitors the presence of an AC
input signal.
Bias Current DAC
The bias current from the MAX3798 is optimized to pro-
vide up to 15mA of bias current into a 50
Ω to 75Ω
VCSEL load with 40μA resolution. The bias current is
controlled through the 3-wire digital interface using the
SET_IBIAS, IBIASMAX, and BIASINC registers.
For VCSEL operation, the IBIASMAX register is first pro-
grammed to a desired maximum bias current value (up
to 15mA). The bias current to the VCSEL then can
range from zero to the value programmed into the
IBIASMAX register. The bias current level is stored in
the 9-bit SET_IBIAS register. Only bits 1 to 8 are written
to. The LSB (bit 0) of SET_IBIAS is initialized to zero
and is updated through the BIASINC register.
The value of the SET_IBIAS DAC register is updated
when the BIASINC register is addressed through the
3-wire interface. The BIASINC register is an 8-bit regis-
ter where the first 5 bits contain the increment informa-
tion in two’s complement notation. Increment values
range from -8 to +7 LSBs. If the updated value of
SET_IBIAS[8:1] exceeds IBIASMAX[7:0], the IBIASERR
warning flag is set and SET_IBIAS[8:0] remains
unchanged.
Modulation Current DAC
The modulation current from the MAX3798 is optimized
to provide up to 12mA of modulation current into a
100
Ω differential load with 40μA resolution. The modu-
lation current is controlled through the 3-wire digital
interface using the SET_IMOD, IMODMAX, MODINC,
and SET_TXDE registers.
For VCSEL operation, the IMODMAX register is first pro-
grammed to a desired maximum modulation current
value (up to 12mA into a 100
Ω differential load). The
modulation current to the VCSEL then can range from
zero to the value programmed into the IMODMAX regis-
ter. The modulation current level is stored in the 9-bit
SET_IMOD register. Only bits 1 to 8 are written to. The
LSB (bit 0) of SET_IMOD is initialized to zero and is
updated through the MODINC register.
The value of the SET_IMOD DAC register is updated
when the MODINC register is addressed through the
3-wire interface. The MODINC register is an 8-bit regis-
ter where the first 5 bits contain the increment informa-
tion in two’s complement notation. Increment values
range from -8 to +7 LSBs. If the updated value of
SET_IMOD[8:1] exceeds IMODMAX[7:0], the IMODERR
warning flag is set and SET_IMOD[8:0] remains
unchanged.
Output Driver
The output driver is optimized for an AC-coupled 100
Ω
differential load. The output stage also features program-
mable deemphasis that allows the deemphasis ampli-
tude to be set as a percentage of the modulation current.
The deemphasis function is enabled by the TXDE_EN
bit. At initial setup the required amount of deemphasis
can be set using the SET_TXDE register. During the
system operation, it is advised to use the incremental
mode that updates the deemphasis (SET_TXDE) and
the modulation current DAC (SET_IMOD) simultaneous-
ly through the MODINC register.
Power-On Reset (POR)
Power-on reset ensures that the laser is off until supply
voltage has reached a specified threshold (2.55V).
After power-on reset, bias current and modulation cur-
rent ramp up slowly to avoid an overshoot. In the case
of a POR, all registers are reset to their default values.
Bias Current Monitor
Current out of the BMON pin is typically 1/16th the
value of IBIAS. A resistor to ground at BMON sets the
voltage gain. An internal comparator latches a SOFT
FAULT if the voltage on BMON exceeds the value of
VCC - 0.55V.
VCSEL Current Limiter
To ensure an enhanced eye safety, an external analog
VCSEL current limitation can be used in addition to the
digital one. An external resistor at BMAX and MMAX
limits the maximum bias and modulation currents,
respectively. A HARD FAULT condition is latched if the
VCSEL current exceeds this threshold.
Eye Safety and Output Control Circuitry
The safety and output control circuitry contains a dis-
able pin (DISABLE) and disable bit (TX_EN), along with
a FAULT indicator and fault detectors (Figure 3). The
MAX3798 has two types of faults, HARD FAULT and
SOFT FAULT. A HARD FAULT triggers the FAULT pin
and the output to the VCSEL is disabled. A SOFT
FAULT operates more like a warning and the outputs
are not disabled. Both types of faults are stored in the
TXSTAT1 and TXSTAT2 registers.
The FAULT pin is a latched output that can be cleared by
toggling the DISABLE pin. Toggling the DISABLE pin also
clears the TXSTAT1 and TXSTAT2 registers. A single-
point fault can be a short to VCC or GND. Table 3 shows
the circuit response to various single-point failures.
MAX3798
1.0625Gbps to 10.32Gbps, Integrated, Low-
Power SFP+ Limiting Amplifier and VCSEL Driver
______________________________________________________________________________________
17
相关PDF资料 |
PDF描述 |
|---|---|
| MAX400CPA+ | IC OPAMP ULTRA LOW OFFSET 8-DIP |
| MAX4020EEE+ | IC OP AMP SNGL SPLY R-R 16-QSOP |
| MAX4022ESD+ | IC BUFFER R-R 14-SOIC |
| MAX4039EUB+T | IC OP AMP R-R W/REF 10-UMAX |
| MAX4044ESD+T | IC OP AMP R-R QUAD 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3799E/D | 功能描述:限幅放大器 1Gbps to 14Gbps SFP+ Multirate Limiting Amplifier and VCSEL Driver RoHS:否 制造商:Micrel 输入电压范围（最大值）:3.6 V 工作电源电压:3.3 V 电源电流:40 mA 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Tube |
| MAX3799ETJ+ | 功能描述:限幅放大器 1-14Gbps SFP w/VCSEL Driver RoHS:否 制造商:Micrel 输入电压范围（最大值）:3.6 V 工作电源电压:3.3 V 电源电流:40 mA 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Tube |
| MAX3799ETJ+T | 功能描述:限幅放大器 1-14Gbps SFP w/VCSEL Driver RoHS:否 制造商:Micrel 输入电压范围（最大值）:3.6 V 工作电源电压:3.3 V 电源电流:40 mA 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Tube |
| MAX3799EVKIT+ | 功能描述:限幅放大器 Maxim Evaluation Kit RoHS:否 制造商:Micrel 输入电压范围（最大值）:3.6 V 工作电源电压:3.3 V 电源电流:40 mA 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Tube |
| MAX379C/D | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。