- 您现在的位置：买卖IC网 > PDF目录2088 > MAX3845UCQ+TD (Maxim Integrated Products)IC SW/CBL DRVR DVI/HDMI 100TQFP PDF资料下载
参数资料
| 型号： | MAX3845UCQ+TD |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/19页 |
| 文件大小： | 0K |
| 描述： | IC SW/CBL DRVR DVI/HDMI 100TQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 250 |
| 类型： | HDMI/DVI 开关 |
| 应用： | HDMI，DVI，接收器 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TQFP 裸露焊盘 |
| 供应商设备封装： | 100-TQFP-EP（14x14） |
| 包装： | 带卷 (TR) |
MAX3845
DVI/HDMI 2:4 TMDS Fanout Switch and
Cable Driver
8
_______________________________________________________________________________________
Detailed Description
The MAX3845 2:4 DVI/HDMI fanout switch and cable
driver accept differential CML input data at rates of
250Mbps up to 1.65Gbps (individual channel data
rate). The input portion of the device consists of two
independent TMDS inputs, each having four fixed-level
equalizers, four limiting amplifiers, a loss-of-signal
(LOS) detector, and power-down control. The output
portion of the device consists of four independent
TMDS outputs, each having four multiplexers, four out-
put buffers with selectable preemphasis, HOTPLUG
detection, and channel selection control (Figure 1).
Fixed Input Equalization
All four differential pairs on the MAX3845’s TMDS
inputs have fixed-level equalizers to compensate for 0in
to 6in of FR4 PCB losses. The signal boost is approxi-
mately 1dB at 825MHz. If more equalization is desired,
use the MAX3814 or MAX3815 in front of the MAX3845
to accommodate long cable lengths.
Limiting Amplifiers
Limiting amplifiers follow the equalizer block to ensure
proper signal levels are achieved for the multiplexers.
Loss-of-Signal (LOS) Detectors
Input channel 1 has an LOS detector attached to the
IN1_B pair. For input channel 2 the LOS detector is
attached to the IN2_C pair. If the received-signal ampli-
tude is smaller than 150mVP-P (typical) at IN1_B, all
output channels selected to input 1 are muted.
Likewise, if a signal smaller than 150mVP-P (typical) is
at IN2_C, all output channels selected to input 2 are
muted.
Multiplexers
Each MAX3845 output has four multiplexers, one for
each signal pair contained in the TMDS channel. These
connect the output to either input 1 or input 2. The
IN_SELx pins control the multiplexers.
Preemphasis Drivers
The preemphasis drivers have three selectable levels
of preemphasis: 0dB, 3dB, and 6dB. The preemphasis
drivers provide a precompensated signal that allows for
extended length cables to be used at the output.
Applications Information
MAX3845 in HDMI 1.3 Systems
The MAX3845 is designed and characterized to oper-
ate from 250Mbps to 1.65Gbps. HDMI 1.3 specifies up
to 2.25Gbps for 1080p “deep color” and allows a maxi-
mum data rate of 3.4Gbps on each of the three data
pairs. The MAX3845 operates normally in an HDMI 1.3
system up to 1.65Gbps. The MAX3845 operates at data
rates above 1.65Gbps with reduced jitter performance.
See the
Typical Operating Characteristics section for
more information.
MAX3845 in HDCP Systems
High-bandwidth digital content protection (HDCP) is a
copy protection system employed in some DVI and
most HDMI interfaces. Video data is encrypted at the
transmitter and decrypted at the receiver. The data
scrambling is dependent upon shared keys established
during the authentication protocol that occurs over the
DDC channel (between the video source and the dis-
play). The MAX3845 does not decrypt or reencrypt
data. Therefore, HDCP-encrypted video routed through
the MAX3845 is only viewable on the display to which
the DDC channel is connected. For applications that
employ HDCP, the MAX3845 acts as a dual 1:4 switch
and not as a fanout device. This means that one video
source can be selected to drive any one of four dis-
plays, but the video source cannot be replicated on
more than one display at the time. Fanout is possible in
non-HDCP applications, allowing one video source to
simultaneously drive up to four displays.
Output Level Control, Back Termination,
and AC-Coupling
The OUT_LEVEL pin is an LVTTL input that allows the
user to select between standard output drive current
(11mA) or increased output drive current (14mA). The
increased output current setting allows back termina-
tion resistors to be used on the outputs. The use of
back terminations is highly recommended for best sig-
nal integrity (see Figures 2 and 3).
If OUT_LEVEL is set low, the standard output drive cur-
rent (11mA) is consistent with DVI/HDMI architecture
and common-mode levels. As per standard, no back
termination is used so no reflected energy can be
absorbed.
If OUT_LEVEL is set high, the output drive current is
increased to 14mA and allows the use of back termina-
tion resistors. Two options are available: a differential
back termination resistor or two single-ended pullup
resistors (see Figures 2 and 3).
相关PDF资料 |
PDF描述 |
|---|---|
| MAX384EPN | IC MUX 8CH DUAL 4CH LTCHBL 18DIP |
| MAX3861EGG | IC POST AMP 2.7GBPS W/AGC 24TQFN |
| MAX3945ETE+ | IC AMP LIMITING 3.3V LP 16TQFN |
| MAX3964AETP+T | IC AMP LIMITING SGNL DET 20-TQFN |
| MAX3969ETP+T | IC AMP LIMIT 200MBPS 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX384C/D | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX384CPN | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX384CWN | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX384CWN+ | 功能描述:多路器开关 IC 4:1 2Ch Low Voltage MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX384CWN+T | 功能描述:多路器开关 IC 4:1 2Ch Low Voltage MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。