- 您现在的位置：买卖IC网 > PDF目录20055 > MAX3863ETJ+ (Maxim Integrated)IC LASR DRVR 2.7GBPS 3.6V 32TQFN PDF资料下载
参数资料
| 型号： | MAX3863ETJ+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 7/15页 |
| 文件大小： | 0K |
| 描述： | IC LASR DRVR 2.7GBPS 3.6V 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 激光二极管驱动器（光纤） |
| 数据速率： | 2.7Gbps |
| 通道数： | 1 |
| 电源电压： | 3.15 V ~ 3.6 V |
| 电流 - 电源： | 58mA |
| 电流 - 调制： | 80mA |
| 电流 - 偏置： | 100mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
2.7Gbps Laser Driver with Modulation
Compensation
V CC
A - TOKO FSLB2520-330K
B - MURATA BLM11HA601SPT
V CC
A
A
DATA+
50 Ω
DATA+
V CC
B
B
25 Ω
DATA-
50 Ω
DATA-
MODN
V CC
V CC
MAX3863
MOD
0.1 μ F
50 Ω
OSCILLOSCOPE
CLK+
50 Ω
CLK+
APCFILT1
0.1 μ F
50 Ω
50 Ω
V CC
CLK-
50 Ω
CLK-
RTEN
EN
BIAS
15 Ω
Figure 1. AC Characterization
Detailed Description
The MAX3863 laser driver has two main components: a
high-speed modulation driver and a biasing block with
APC. The clock and data inputs to the modulation driver
use CML logic levels. The optional clock signal synchro-
nizes data transitions for minimum pattern-dependent jit-
ter. Outputs to the laser diode consist of a switched
modulation current and a steady bias current. The APC
loop adjusts the laser diode bias current to maintain con-
stant average optical power. Compensation of the modu-
lation current can be programmed to keep a constant
extinction ratio over time and temperature. The modula-
tion output stage uses a programmable current source
with a maximum current of 80mA. A high-speed differen-
tial pair switches the source to the laser diode. The rise
and fall times are typically 50ps.
Optional Input Data Retiming
To eliminate pattern-dependent jitter in the input data, a
synchronous differential clock signal should be con-
nected to the CLK+ and CLK- inputs, and the RTEN
control input should be connected low. The input data
is retimed on the rising edge of CLK+. If RTEN is tied
high or is left floating, the retiming function is disabled,
and the input data is directly connected to the output
stage. Leave CLK+ and CLK- open when retiming is
disabled.
Mark-Density Outputs
The MK+ and MK- outputs monitor the input signal
mark density. With a 50% mark density, both outputs
are the same voltage. More ones cause the MK+ volt-
age to increase and the MK- voltage to decrease.
Fewer ones than zeros cause MK- to be at a higher
voltage than MK+.
Pulse-Width Control
A pulse-width adjustment range of 50% to 150%
(±185ps) is available at 2.7Gbps. This feature compen-
sates pulse-width distortion elsewhere in the system.
Resistors at the PWC+ and PWC- pins program the
pulse width. The sum of the resistors is 1k Ω . The pins
can be left open for a 100% pulse width. A voltage also
can control these pins. A differential voltage of 600mV
(typ) gives ±185ps of pulse-width distortion.
Output Enable
The MAX3863 incorporates an input to enable current
to the laser diode. When EN is low, the modulation and
bias outputs at the MOD pin are enabled. When EN is
high or floating, the output is disabled. In the disabled
condition, bias and modulation currents are off.
Power-Supply Threshold
To prevent data errors caused by low supply, the
MAX3863 disables the laser diode current for supply
voltage less than 2.7V. The power-supply threshold and
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| T86D157M004EAAL | CAP TANT 150UF 4V 20% 2917 |
| EBM28MMWD | CARDEDGE MALE 56POS .156 T/H AU |
| GRM1885C1H5R1DZ01D | CAP CER 5.1PF 50V NP0 0603 |
| MENB1050A0503N01 | POWER SUPPLY SWITCHER 30W 5V |
| UP2C-330-R | INDUCTOR POWER 33UH 2.16A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3863ETJ+ | 功能描述:激光驱动器 2.7Gbps Laser Driver w/Modulation Comp RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3863ETJ+T | 功能描述:激光驱动器 2.7Gbps Laser Driver w/Modulation Comp RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3863EVKIT | 功能描述:激光驱动器 Evaluation Kit for the MAX3863 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3864E/D | 功能描述:跨阻抗放大器 MAX3864E/D RoHS:否 制造商:Maxim Integrated 封装 / 箱体: 带宽: 工作电源电压: 电源电流: 工作温度范围: 封装: |
| MAX3864E/D+C8R | 制造商:Maxim Integrated Products 功能描述:2.5GBPS, +3V TO +5.5V, WIDE DYNAMIC RANG |
发布紧急采购，3分钟左右您将得到回复。