- 您现在的位置：买卖IC网 > PDF目录20023 > MAX4273ESE+ (Maxim Integrated)IC CNTRLR HOT SWAP 16-SOIC PDF资料下载
参数资料
| 型号： | MAX4273ESE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 13/26页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR HOT SWAP 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 2.7 V ~ 13.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
3V to 12V Current-Limiting Hot-Swap Controllers
with Autoretry, DualSpeed/BiLevel Fault Protection
In each case, when a fault is encountered, the status
pin (STAT) goes low, and for the MAX4273, the device
discharges the output voltage through a 1k Ω resistor
from LLMON to GND. After a fault, the MAX4271 stays
latched off and the MAX4272 enters retry mode, while
the MAX4273 has selectable latched or retry mode.
Figure 4 shows the waveforms of a fault condition.
BiLevel Fault Protection
Slow Comparator
The slow comparator is disabled at startup while the
external MOSFET is turning on. This allows the part to
ignore the higher-than-normal inrush current charging
the board capacitors when a card is first plugged in.
If the slow comparator detects an overload condition
while in normal operation (after startup is completed), it
turns off the external MOSFET by discharging the gate
capacitance with a 200μA current. The slow compara-
tor threshold is set at 50mV and has a default delay of
20μs (CSPD floating), allowing it to ignore power-sup-
ply glitches and noise. The response time can be
lengthened with an external capacitor at CSPD (Figure
10).
If the overcurrent condition is not continuous, then the
duration above the threshold minus the duration below
must be greater than 20μs (or the external programmed
value) for the device to trip. When the current is above
the threshold, CSPD is charged with a 6μA current
the trip point of 1.2V. Therefore, a pulsing current with a
duty cycle of 50% or greater (i.e., the current is above
the threshold level > 50% of the time) is considered a
fault condition even if it is never higher than the thresh-
old for longer than the slow comparator’s set response
time.
The discharge rate depends on the N-FET gate capaci-
tance and the external capacitance at GATE. In the
MAX4273, CEXT remains connected and capacitance
to this point has to be discharged by the same current.
This increases the discharge time. Once the fault con-
dition is detected, the STAT pin goes low and the
device goes into retry or latched mode.
Fast Comparator
The fast comparator behaves differently according to
the operating mode.
During startup, the fast comparator is part of a simple
current regulator. When the sensed current is above
the fast comparator threshold, the gate is discharged
with a 70μA current source. When the sensed current
drops below the threshold, the charge pump turns on
again. The sensed current will rise and fall near the
threshold due to the fast comparator and charge-pump
propagation delay. The gate voltage will be roughly
sawtooth shaped, and the load current will present a
20% ripple. The ripple can be reduced by adding a
capacitor from GATE to GND.
source. A fault is detected when CSPD is charged to
STAT
ON
STAT
t START
2.7V TO 6V
V GATE
V OUT
V GATE
V OUT
2.7V TO 6V
V GATE
V OUT
I FAST, SET
V TH
C BOARD = LARGE
C BOARD = 0
I LIM
I LOAD
t ON
I LOAD
t OFF
Figure 3. Startup Waveforms
Figure 4. Response to a Fault Condition
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| ISL9021IIJZ-T | IC REG LDO 2.8V .25A 4-WLCSP |
| WSU240-0750 | POWER SUPPLY 100-240V 750MA |
| CAT28C512L12 | IC EEPROM 512KBIT 120NS 32DIP |
| VI-2TT-CX | CONVERTER MOD DC/DC 6.5V 75W |
| CAT28C512GI12 | IC EEPROM 512KBIT 120NS 32PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4273ESE+ | 功能描述:热插拔功率分布 3-12V Current-Limit Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX4273ESE+T | 功能描述:热插拔功率分布 3-12V Current-Limit Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX4273ESE-T | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX4273EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX4274ABESA | 功能描述:运算放大器 - 运放 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。