- 您现在的位置：买卖IC网 > PDF目录1941 > MAX459CQH-D (Maxim Integrated Products)IC VIDEO CROSSPOINT SWIT 44PLCC PDF资料下载
参数资料
| 型号： | MAX459CQH-D |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/17页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO CROSSPOINT SWIT 44PLCC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 28 |
| 功能： | 视频交叉点开关 |
| 电路： | 1 x 8:4 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 管件 |
MAX458/MAX459
8x4 Video Crosspoint Switches with Buffers
_______________________________________________________________________________________
9
_______________Detailed Description
Analog Section
The MAX458/MAX459 video crosspoint switches consist
of a high-speed 32 (8x4) switch array with wide-band-
width line drivers (Figure 1). This design allows make-
before-break switching to reduce output noise and
glitches, but the inputs will not short together. It also pro-
vides high input impedance and low input capacitance,
so no input buffer amplifier is needed. However,
because different transistors provide gain depending on
the input selection, the DC offset voltage shifts slightly
when a new input is switched in. The change in offset
voltage is typically 3mV.
All output buffers will drive back-terminated 50
, 75,
or higher impedance lines with up to 100pF capaci-
tance. The amplifier outputs can be disabled, which is
useful for creating large arrays. When disabled, the
MAX458 presents an output impedance of approxi-
mately 1M
. The MAX459 disabled output impedance
is 1k
(to ground), due to the internal feedback resis-
tors used to achieve the gain of two.
During power-on, if
–
C
—
S
–
and
–
U
—
P
—
D
—
A
—
T
—
E
–
are held high, all
output amplifiers are disabled. In a large array, this
feature prevents two ON paralleled amplifiers from dis-
torting each other’s signals. The amplifiers can be pro-
grammed to come up in any state simultaneously at any
time after power-on. See the Creating Large Arrays
section.
Digital Section—Parallel Mode
The MAX458/MAX459 have two register banks—an
input register and a switch register (Figure 2). Each of
these registers is either latched (when the control input
is high) or transparent (when the control input is low).
The input register is controlled by
–
W
—
R
–
and
–
C
—
E
–
and is
selected by the decode of A0 and A1. If both
–
W
—
R
–
and
–
C
—
E
–
are low, the input register selected by A0 and A1 is
transparent, and the state of D0–D3 is presented to the
switch register. The other three input registers remain
latched. If D0–D3 change before
–
U
—
P
—
D
—
A
—
T
—
E
–
is asserted
(goes low), the new data (the changed D0–D3) will then
be latched in the switch register. If
–
W
—
R
–
or
–
C
—
E
–
is high, all
input registers are latched and their data is presented
Table 1. Amplifier Selection
Table 2. Input Selection
Table 3. Writing Data
H
L
H
L
–
U
—
P
—
D
—
A
—
T
—
E
–
L
H
X
H
X
H
X
H
L
All switch registers and selected input regis-
ter are transparent. Selected amplifier (cho-
sen by state of A0, A1) reflects input data.
Other amplifiers reflect data that had been
latched into the input registers previously.
Input register of selected amplifier is trans-
parent. Switch registers are latched. Other
input registers are latched.
Data in input registers passes through
switch registers. Output reflects data in
input registers.
Device not selected or is operating in seri-
al mode. Both registers are latched.
FUNCTION
–
W
—
R
–
C
—
E
–
X
H
X
Disable output amplifier
selected by A0, A1.
H
L
H
L
H
L
H
7
6
5
4
H
L
H
L
H
D0
D1
L
3
2
1
0
Input Channel Selected
D2
D3
H
L
H
L
H
3
2
1
0
Output Amplifier Selected
A0
A1
MAX458
MAX459
CS
SCLK
WR
CE
A0
A1
D0
D1
D2
D3
DOUT
SHDN
DIN
VCC
UPDATE
WRITE
AMPLIFIER SELECT A0
CHIP ENABLE (SELECT)
AMPLIFIER SELECT A1
DATA BIT D0
DATA BIT D1
DATA BIT D2
SHUTDOWN
DATA BIT D3
40
39
37
36
26
25
24
23
22
19
1
20
21
38
UPDATE
Pin numbers apply to DIP package.
Figure 3. Parallel Connection (only logic pins shown)
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4603EAE | IC SWITCH QUAD SPST 16SSOP |
| MAX4604CPE | IC SWITCH QUAD SPST 16DIP |
| MAX4609CPE | IC SWITCH DUAL SPST 16DIP |
| MAX4612CSD | IC SWITCH QUAD SPST 14SOIC |
| MAX4613CUE | IC SWITCH QUAD SPST 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX459CQH-DW | 功能描述:模拟和数字交叉点 IC RoHS:否 制造商:Micrel 配置:2 x 2 封装 / 箱体:MLF-16 数据速率:10.7 Gbps 输入电平:CML, LVDS, LVPECL 输出电平:CML 电源电压-最大:3.6 V 电源电压-最小:2.375 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 产品:Digital Crosspoint 封装:Tube |
| MAX459CQH-DW-T | 功能描述:模拟和数字交叉点 IC RoHS:否 制造商:Micrel 配置:2 x 2 封装 / 箱体:MLF-16 数据速率:10.7 Gbps 输入电平:CML, LVDS, LVPECL 输出电平:CML 电源电压-最大:3.6 V 电源电压-最小:2.375 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 产品:Digital Crosspoint 封装:Tube |
| MAX459CQH-TD | 功能描述:视频开关 IC RoHS:否 制造商:Texas Instruments 开关数量:4 开启电阻（最大值）:12 Ohms 传播延迟时间: 开启时间（最大值）: 关闭时间（最大值）: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WQFN-42 封装:Reel |
| MAX459EPL | 功能描述:视频开关 IC RoHS:否 制造商:Texas Instruments 开关数量:4 开启电阻（最大值）:12 Ohms 传播延迟时间: 开启时间（最大值）: 关闭时间（最大值）: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WQFN-42 封装:Reel |
| MAX459EVKIT-PLC | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。