- 您现在的位置：买卖IC网 > PDF目录15134 > MAX5041EAI+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 28-SSOP PDF资料下载
参数资料
| 型号： | MAX5041EAI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/26页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 90% |
| 电源电压： | 4.75 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
Dual-Phase, Parallelable, Average Current-Mode
Controllers
V IN and V CC
The MAX5038/MAX5041 accept a wide input voltage
range of +4.75V to +5.5V or +8V to +28V. All internal
control circuitry operates from an internally regulated
nominal voltage of +5V (V CC ). For input voltages of +8V
or greater, the internal V CC regulator steps the voltage
down to +5V. The V CC output voltage regulates to +5V
while sourcing up to 80mA. Bypass V CC to SGND with
4.7μF and 0.1μF low-ESR ceramic capacitors for high-
frequency noise rejection and stable operation (Figures 1
and 2).
Calculate power dissipation in the MAX5038/MAX5041
as a product of the input voltage and the total V CC reg-
ulator output current (I CC ). I CC includes quiescent cur-
rent (I Q ) and gate drive current (I DD ):
P D = V IN x I CC (1)
I CC = I Q + f SW x (Q G1 + Q G2 + Q G3 + Q G4 ) (2)
where, Q G1 , Q G2 , Q G3, and Q G4 are the total gate
charge of the low-side and high-side external
MOSFETs, I Q is 4mA (typ), and f SW is the switching fre-
quency of each individual phase.
For applications utilizing a +5V input voltage, disable
the V CC regulator by connecting IN and V CC together.
Undervoltage Lockout (UVLO)/
Power-On Reset (POR)/Soft-Start
The MAX5038/MAX5041 include an undervoltage lock-
out with hysteresis and a power-on reset circuit for con-
verter turn-on and monotonic rise of the output voltage.
The UVLO threshold is internally set between +4.0V
and +4.5V with a 200mV hysteresis. Hysteresis at
UVLO eliminates “chattering” during startup.
Most of the internal circuitry, including the oscillator,
turns on when the input voltage reaches +4V. The
MAX5038/MAX5041 draw up to 4mA of current before
the input voltage reaches the UVLO threshold.
The compensation network at the current error ampli-
fiers (CLP1 and CLP2) provides an inherent soft-start of
the output voltage. It includes a parallel combination of
capacitors (C28, C30) and resistors (R5, R6) in series
with other capacitors (C27, C29) (see Figures 1 and 2).
The voltage at CLP_ limits the maximum current avail-
able to charge output capacitors. The capacitor on
CLP_ in conjunction with the finite output-drive current
of the current-error amplifier yields a finite rise time for
the output current and thus the output voltage.
Internal Oscillator
The internal oscillator generates the 180° out-of-phase
clock signals required by the pulse-width modulation
(PWM) circuits. The oscillator also generates the 2V P-P
voltage ramp signals necessary for the PWM compara-
tors. Connect CLKIN to SGND to set the internal oscillator
frequency to 250kHz or connect CLKIN to V CC to set the
internal oscillator to 500kHz.
CLKIN is a CMOS logic clock input for the phase-
locked loop (PLL). When driven externally, the internal
oscillator locks to the signal at CLKIN. A rising edge at
CLKIN starts the ON cycle of the PWM. Ensure that the
external clock pulse width is at least 200ns. CLKOUT
provides a phase-shifted output with respect to the ris-
ing edge of the signal at CLKIN. PHASE sets the
amount of phase shift at CLKOUT. Connect PHASE to
V CC for 120° of phase shift, leave PHASE unconnected
for 90° of phase shift, or connect PHASE to SGND for
60° of phase shift with respect to CLKIN.
The MAX5038/MAX5041 require compensation on
PLLCMP even when operating from the internal oscillator.
The device requires an active PLL in order to generate
the proper clock signal required for PWM operation.
Control Loop
The MAX5038/MAX5041 use an average current-mode
control scheme to regulate the output voltage (Figures
3a and 3b). The main control loop consists of an inner
current loop and an outer voltage loop. The inner loop
controls the output currents (I PHASE1 and I PHASE2 )
while the outer loop controls the output voltage. The
inner current loop absorbs the inductor pole reducing
the order of the outer voltage loop to that of a single-
pole system.
The current loop consists of a current-sense resistor
(R S ), a current-sense amplifier (CA_), a current-error
amplifier (CEA_), an oscillator providing the carrier
ramp, and a PWM comparator (CPWM_). The precision
CA_ amplifies the sense voltage across R S by a factor
of 18. The inverting input to the CEA_ senses the CA_
output. The CEA_ output is the difference between the
voltage-error amplifier output (EAOUT) and the gained-
up voltage from the CA_. The RC compensation net-
work connected to CLP1 and CLP2 provides external
frequency compensation for the respective CEA_. The
start of every clock cycle enables the high-side drivers
and initiates a PWM ON cycle. Comparator CPWM_
compares the output voltage from the CEA_ with a 0 to
+2V ramp from the oscillator. The PWM ON cycle termi-
nates when the ramp voltage exceeds the error voltage.
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| URS1V332MRD | CAP ALUM 3300UF 35V 20% RADIAL |
| SLPX392M063E3P3 | CAP ALUM 3900UF 63V 20% SNAP |
| SLPX153M025E3P3 | CAP ALUM 15000UF 25V 20% SNAP |
| SLP331M220C1P3 | CAP ALUM 330UF 220V 20% SNAP |
| H2BBG-10104-Y8-ND | JUMPER-H1501TR/A3048Y/H1501TR 4" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5041EAI+ | 功能描述:电流型 PWM 控制器 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5041EAI+T | 功能描述:电流型 PWM 控制器 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5041EAI+TG48 | 制造商:Maxim Integrated Products 功能描述:N/A - Tape and Reel |
| MAX5041EAI-T | 功能描述:电流型 PWM 控制器 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5041EAI-TG48 | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, PARALLELABLE, AVERAGE CURRENT-MODE CONTROLLERS - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。