参数资料
型号: MAX5041EAI+
厂商: Maxim Integrated Products
文件页数: 25/26页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 28-SSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 46
PWM 型: 电流模式
输出数: 1
频率 - 最大: 1MHz
占空比: 90%
电源电压: 4.75 V ~ 28 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: 28-SSOP(0.209",5.30mm 宽)
包装: 管件
Dual-Phase, Parallelable, Average Current-Mode
Controllers
Use the following equations to calculate C CF and C CFF :
Pin Configuration
C CF =
1
2 × π × f Z × R CF
(30)
TOP VIEW
CSP2 1
28 CLKIN
C CFF =
1
2 × π × f P × R CF
(31)
CSN2 2
PHASE 3
27 CLKOUT
26 BST2
PC Board Layout
PLLCMP 4
25 DH2
Use the following guidelines to layout the switching
voltage regulator.
1) Place the V IN and V CC bypass capacitors close to
the MAX5038/MAX5041.
2) Minimize the high-current loops from the input
capacitor, upper switching MOSFET, inductor, and
output capacitor back to the input capacitor nega-
tive terminal.
3) Keep short the current loop from the lower switch-
ing MOSFET, inductor, and output capacitor and
return to the source of the lower MOSFET.
4) Place the Schottky diodes close to the lower
MOSFETs and on the same side of the PC board.
5) Keep the SGND and PGND isolated and connect
CLP2 5
SGND 6
CLP1 7
SENSE+ 8
SENSE- 9
DIFF 10
EAN 11
EAOUT 12
CSP1 13
CSN1 14
MAX5038A
MAX5041A
SSOP
24 LX2
23 DL2
22 PGND
21 IN
20 V CC
19 DL1
18 LX1
17 DH1
16 BST1
15 EN
them at one single point close to the negative termi-
nal of the input filter capacitor.
6) Run the current-sense lines CS+ and CS- very
close to each other to minimize the loop area.
Similarly, run the remote voltage sense lines
SENSE+ and SENSE- close to each other. Do not
cross these critical signal lines through power cir-
cuitry. Sense the current right at the pads of cur-
rent-sense resistors.
7) Avoid long traces between the V CC bypass capaci-
tors, driver output of the MAX5038/MAX5041,
MOSFET gates and PGND pin. Minimize the loop
formed by the V CC bypass capacitors, bootstrap
diode, bootstrap capacitor, MAX5038/MAX5041,
and upper MOSFET gate.
8) Place the bank of output capacitors close to the load.
9) Distribute the power components evenly across the
board for proper heat dissipation.
10) Provide enough copper area at and around the
switching MOSFETs, inductor, and sense resistors
to aid in thermal dissipation.
11) Use at least 4oz copper to keep the trace induc-
tance and resistance to a minimum. Thin copper PC
boards can compromise efficiency since high cur-
rents are involved in the application. Also, thicker
copper conducts heat more effectively, thereby
reducing thermal impedance.
Chip Information
TRANSISTOR COUNT: 5431
PROCESS: BiCMOS
______________________________________________________________________________________
25
相关PDF资料
PDF描述
URS1V332MRD CAP ALUM 3300UF 35V 20% RADIAL
SLPX392M063E3P3 CAP ALUM 3900UF 63V 20% SNAP
SLPX153M025E3P3 CAP ALUM 15000UF 25V 20% SNAP
SLP331M220C1P3 CAP ALUM 330UF 220V 20% SNAP
H2BBG-10104-Y8-ND JUMPER-H1501TR/A3048Y/H1501TR 4"
相关代理商/技术参数
参数描述
MAX5041EAI+ 功能描述:电流型 PWM 控制器 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5041EAI+T 功能描述:电流型 PWM 控制器 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5041EAI+TG48 制造商:Maxim Integrated Products 功能描述:N/A - Tape and Reel
MAX5041EAI-T 功能描述:电流型 PWM 控制器 Dual-Phase Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5041EAI-TG48 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, PARALLELABLE, AVERAGE CURRENT-MODE CONTROLLERS - Tape and Reel