- 您现在的位置：买卖IC网 > PDF目录17226 > MAX5060EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX5060 PDF资料下载
参数资料
| 型号： | MAX5060EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/31页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX5060 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 20A |
| 输入电压： | 10 ~ 14V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 270kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX5060 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
0.6V to 5.5V Output, Parallelable,
Average-Current-Mode DC-DC Controllers
where ? I L = peak-to-peak inductor current. Choose
RC2 = 10 ? , V CC = 5.1V, and R SENSE is a current-
sense resistor. Note that the current limit of MAX5061 is
V OUT ( NL ) = [( REF + REF
) × R H ] + V REF
reduced by 3mV / R SENSE .
The no-load output voltage depends on the R H , R F ,
V REF (0.6V) and the fixed DC bias voltage at CSP -
CSN. The following equation assumes a 3mV bias volt-
age at CSP - CSN.
V V ? 0 . 1
R L R F
Adaptive Voltage Positioning
V CNTR +
? V OUT /2
V CNTR
V CNTR -
? V OUT /2
Powering new-generation processors requires new
techniques to reduce cost, size, and power dissipation.
Voltage positioning reduces the total number of output
NO LOAD
1/2 LOAD
LOAD (A)
FULL LOAD
capacitors to meet a given transient response require-
ment. Setting the no-load output voltage slightly higher
than the output voltage during nominally loaded condi-
tions allows a larger downward-voltage excursion when
the output current suddenly increases. Regulating at a
lower output voltage under a heavy load allows a larger
upward-voltage excursion when the output current sud-
denly decreases. Allowing a larger voltage-step excur-
sion reduces the required number of output capacitors
or allows for the use of higher ESR capacitors.
Voltage positioning may require the output to regulate
away from a center value. Define the center value as
the voltage where the output drops ( ? V OUT /2) at one
half the maximum output current (Figure 7).
Set the voltage-positioning window ( ? V OUT ) using the
resistive feedback of the voltage-error amplifier (VEA).
Use the following equations to calculate the voltage-
positioning window (Figure 5):
MAX5060:
Figure 7. Defining the Voltage-Positioning Window
MOSFET Gate Drivers (DH_, DL_)
The high-side (DH) and low-side (DL) drivers drive the
gates of external n-channel MOSFETs (Figures 1 and 2).
The drivers’ 4A peak sink- and source-current capability
provides ample drive for the fast rise and fall times of the
switching MOSFETs. Faster rise and fall times result in
reduced cross-conduction losses. For modern CPU volt-
age-regulating module applications, where the duty
cycle is less than 50%, choose high-side MOSFETs (Q1)
with a moderate R DS(ON) and a very low gate charge.
Choose low-side MOSFETs (Q2) with very low R DS(ON)
and moderate gate charge. Size the high-side and low-
side MOSFETs to handle the peak and RMS currents
during overload conditions.
The driver block also includes a logic circuit that provides
× H L
G C =
MAX5061:
? V OUT =
I OUT × R IN R + R
G C × R F R L
0 . 0289
R S
an adaptive nonoverlap time to prevent shoot-through
currents during transition. The typical nonoverlap time is
35ns between the high-side and low-side MOSFETs.
BST
The MAX5060 uses V DD to power the low- and high-side
MOSFET drivers. The low- and high-side drivers in the
MAX5061 are powered from V CC . The high-side driver
? V OUT = OUT H
I x R
G c x R F
R IN and R F are the input and feedback resistors of
VEA. G C is the current-loop transconductance and R S
is the current-sense resistor.
derives its power through a bootstrap capacitor and V DD
supplies power internally to the low-side driver. Connect a
0.47μF low-ESR ceramic capacitor between BST and LX.
Connect a Schottky rectifier from BST to V DD on the
MAX5060, or to V CC on the MAX5061. Reduce the PC
board area formed by the boost capacitor and rectifier.
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| R1S8-1505/P | CONV DC/DC 1W 15VIN 05VOUT |
| GCA14DCBN | CONN EDGECARD 28POS R/A .125 SLD |
| R1S-2409/P | CONV DC/DC 1W 24VIN 09VOUT |
| GCA14DCBD | CONN EDGECARD 28POS R/A .125 SLD |
| R1S-153.3/P | CONV DC/DC 1W 15VIN 3.3VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5061 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:0.6V to 5.5V Output, Parallelable, Average-Current-Mode DC-DC Controllers |
| MAX5061AUE | 功能描述:DC/DC 开关控制器 .6-5.5V Parallelable Average-Current-Mode RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX5061AUE+ | 功能描述:DC/DC 开关控制器 .6-5.5V Parallelable Average-Current-Mode RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX5061AUE+T | 功能描述:DC/DC 开关控制器 .6-5.5V Parallelable Average-Current-Mode RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX5061AUE-T | 功能描述:DC/DC 开关控制器 .6-5.5V Parallelable Average-Current-Mode RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。