- 您现在的位置：买卖IC网 > PDF目录17247 > MAX5063DASA+ (Maxim Integrated Products)IC MOSFET DRIVER 8-SOIC PDF资料下载
参数资料
| 型号： | MAX5063DASA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC MOSFET DRIVER 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 配置： | 半桥 |
| 输入类型： | 反相和非反相 |
| 延迟时间： | 35ns |
| 电流 - 峰： | 2A |
| 配置数： | 1 |
| 输出数： | 2 |
| 高端电压 - 最大（自引导启动）： | 125V |
| 电源电压： | 8 V ~ 12.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 供应商设备封装： | 8-SOICN 裸露焊盘 |
| 包装： | 管件 |
125V/2A, High-Speed,
Half-Bridge MOSFET Drivers
Topologies like the two-switch forward converter, where
both high- and low-side switches are turned on and off
simultaneously, can have the BBM function disabled by
leaving BBM unconnected. When disabled, t BBM is typi-
cally 1ns.
Driver Logic Inputs (IN_H, IN_L, IN_H+,
IN_H-, IN_L+, IN_L-)
The MAX5062_/MAX5064A are CMOS (V DD / 2) logic-
input drivers while the MAX5063_/MAX5064B have TTL-
compatible logic inputs. The logic-input signals are
independent of V DD . For example, the IC can be pow-
ered by a 10V supply while the logic inputs are provid-
ed from a 12V CMOS logic. Also, the logic inputs are
protected against voltage spikes up to 15V, regardless
shoot-through in the absence of external BBM delay
during the narrow pulse at low duty cycle (see Figure 2).
At high duty cycle (close to 100%) the DH minimum low
pulse width (t DMIN-DH-L ) must be higher than the DL
minimum low pulse width (t DMIN-DL-L ) to avoid overlap
and shoot-through (see Figure 3). In the case of
MAX5062/MAX5063/MAX5064, there is a possibility of
about 40ns overlap if an external BBM delay is not pro-
vided. We recommend adding external delay in the INH
path so that the minimum low pulse width seen at INH
is always longer than t PW-MIN . See the Electrical
Characteristics table for the typical values of t PW-MIN .
V DD
of the V DD voltage. The TTL and CMOS logic inputs
have 400mV and 1.6V hysteresis, respectively, to avoid
double pulsing during transition. The logic inputs are
high-impedance pins and should not be left floating.
A)
V IN
The low 2.5pF input capacitance reduces loading and
increases switching speed. The noninverting inputs are
pulled down to GND and the inverting inputs are pulled
PWM IN
INH
DH
N
V OUT
up to V DD internally using a 1M ? resistor. The PWM
HS
output from the controller must assume a proper state
while powering up the device. With the logic inputs
INL
DL
N
floating, the DH and DL outputs pull low as V DD rises
up above the UVLO threshold.
The MAX5064_ has two logic inputs per driver, which
provide greater flexibility in controlling the MOSFET.
MAX5062B/MAX5062D/MAX5063B/MAX5063D/MAX5064
Use IN_H+/IN_L+ for noninverting logic and IN_H-/
IN_L- for inverting logic operation. Connect
IN_H+/IN_L+ to V DD and IN_H-/IN_L- to GND if not
used. Alternatively, the unused input can be used as an
ON/OFF function. Use IN_+ for active-low and IN_- for
active-high shutdown logic.
Table 1. MAX5064_ Truth Table
B)
PWM IN
t DMIN-DH-H
IN_H+/IN_L+
Low
Low
High
High
IN_H-/IN_L-
Low
High
Low
High
DH/DL
Low
Low
High
Low
DH
Minimum Pulse Width
The MAX5062/MAX5063/MAX5064 uses a single-shot
level shifter architecture to achieve low propagation
delay. Typical level shifter architecture causes a mini-
mum (high or low) pulse width (t DMIN ) at the output that
may be higher than the logic-input pulse width. For
MAX5062/MAX5063/MAX5064 devices, the DH mini-
mum high pulse width (t DMIN-DH-H ) is lower than the DL
minimum low pulse width (t DMIN-DL-L ) to avoid any
BUILT-IN
DEAD TIME
DL
t DMIN-DL-L
Figure 2. Minimum Pulse-Width Behavior for Narrow Duty-
Cycle Input (On-Time < t PW-MIN )
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| ASPI-0804T-681M-T | INDUCTOR POWER 680UH 0804 SMD |
| ECM08DRKN-S13 | CONN EDGECARD 16POS .156 EXTEND |
| RCC18DCSH-S288 | CONN EDGECARD 36POS .100 EXTEND |
| MAX4427CSA+ | IC MOSFET DRV DUAL NONINV 8-SOIC |
| MAX4429CPA+ | IC DRIVER MOSFET SNGL 6A HS 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5063DASA+ | 功能描述:功率驱动器IC 125V 2A Half-Bridge MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX5063DASA+T | 功能描述:功率驱动器IC 125V 2A Half-Bridge MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX5063DASA-T | 功能描述:功率驱动器IC 125V 2A Half-Bridge MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX5064AATC | 功能描述:功率驱动器IC 125V 2A Half-Bridge MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX5064AATC+ | 功能描述:功率驱动器IC 125V 2A Half-Bridge MOSFET Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。