- 您现在的位置：买卖IC网 > PDF目录17225 > MAX5069EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX5069 PDF资料下载
参数资料
| 型号： | MAX5069EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/19页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX5069 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，隔离 |
| 输出电压： | 12V |
| 电流 - 输出： | 10A |
| 输入电压： | 36 ~ 72V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 500kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX5069 |
High-Frequency, Current-Mode PWM Controller
with Accurate Oscillator and Dual FET Drivers
Oscillator/Switching Frequency
Use an external resistor at RT to program the MAX5069
internal oscillator frequency from 50kHz to 2.5MHz. The
MAX5069 NDRVA/NDRVB switching frequency is one
half of the programmed oscillator frequency with a
maximum 50% duty cycle.
Use the following formula to calculate the internal oscil-
shorting out the transformer’s primary. The MAX5069
allows the dead-time delay required to turn on the
NDRVB FET after the NDRVA FET turns off. The dead
time can be programmed to a minimum of 30ns to 1 / (0.5
x f SW ). Connect a resistor between DT and AGND to set
the desired dead time. Calculate the dead time using the
following formula:
10
Dead time =
× R DT ( ns )
lator frequency:
f osc =
11
R RT
60
29 . 4
where R DT is in k ? and the dead time is in ns.
where f OSC is the oscillator frequency and R RT is a
resistor connected from RT to AGND.
Choose the appropriate resistor at RT to calculate the
desired switching frequency (f SW ):
External Synchronization (MAX5069A/D)
The MAX5069A/D can be synchronized using an exter-
nal clock at the SYNC input. For proper frequency syn-
chronization, the SYNC’s input frequency must be at
least 25% higher than the MAX5069A/D programmed
R RT =
10 11
2 f SW
internal oscillator frequency. Connect SYNC to AGND
when not using an external clock.
For the maximum 50% duty cycle at NDRVA/NDRVB,
connect DT to REG5.
Dual N-Channel MOSFET Switch Driver
The MAX5069 drives two external N-channel MOSFETs
in push-pull isolated power supplies. Each MOSFET
driver operates with a maximum 50% duty cycle. The
NDRV_ outputs are supplied by the internal regulator
(V CC ), which is internally set to approximately 9.5V. For
the universal input voltage range, the MOSFETs used
must be able to withstand at least twice the DC level of
the high-line input voltage. Both NDRVA and NDRVB
can source and sink in excess of 650mA and 1000mA
peak current, respectively.
Dead-Time Control
In typical push-pull designs, it is desirable to add some
extra delay between the turning off of one MOSFET and
the turning on of the next MOSFET (Figure 7). The extra
time ensures that the first MOSFET is fully off when the
other MOSFET starts to turn on. This prevents both
MOSFETs from being on simultaneously, thus avoiding
Integrating Fault Protection
The integrating fault-protection feature allows transient
overcurrent conditions to be ignored for a programma-
ble amount of time, giving the power supply time to
behave like a current source to the load. For example,
this can occur under load-current transients when the
control loop requests maximum current to keep the out-
put voltage from going out of regulation. Program the
fault-integration time by connecting an external suitably
sized capacitor to the FLTINT. Under sustained over-
current faults, the voltage across this capacitor ramps
up towards the FLTINT shutdown threshold (typically
2.8V). Once the threshold is reached, the power supply
shuts down. A high-value bleed resistor connected in
parallel with the FLTINT capacitor allows it to discharge
towards the restart threshold (typically 1.6V). Once this
threshold is reached, the supply restarts with a new
soft-start cycle.
SYNC
MAX5069A/D
DEAD TIME
NDRVA
PWM
t DT
<50%
RT
NDRVB
PWM
<50%
AGND
Figure 7. MAX5069 Dead-Time Timing Diagram
Figure 8. External Synchronization of the MAX5069A/D
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| R1D10-3.305 | CONV DC/DC 1W 3.3VIN +/-05VOUT |
| CDBMH240-HF | DIODE SCHOTTKY 40V 2.0A SOD123T |
| CDBMH230-HF | DIODE SCHOTTKY 30V 2.0A SOD123T |
| CDBMH220-HF | DIODE SCHOTTKY 20V 2.0A SOD123T |
| CDBM260-G | DIODE SCHOTTKY 60V 2.0A SOD123 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX506ACPP | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACPP+ | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACWP | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACWP+ | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACWP+T | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。