- 您现在的位置：买卖IC网 > PDF目录17225 > MAX5069EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX5069 PDF资料下载
参数资料
| 型号： | MAX5069EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/19页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX5069 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，隔离 |
| 输出电压： | 12V |
| 电流 - 输出： | 10A |
| 输入电压： | 36 ~ 72V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 500kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX5069 |
High-Frequency, Current-Mode PWM Controller
with Accurate Oscillator and Dual FET Drivers
Current Limit
The current-sense resistor (R CS ), connected between
the source of the MOSFET and ground, sets the current
limit. The CS input has a voltage trip level (V CS ) of
314mV. Use the following equation to calculate the
value of R CS :
Applications Information
Layout Recommendations
Keep all PC board traces carrying switching currents
as short as possible, and minimize current loops.
For universal AC input design, follow all applicable safe-
ty regulations. Offline power supplies may require UL,
R CS =
V CS
I PRI
VDE, and other similar agency approvals. Contact these
agencies for the latest layout and component rules.
where I PRI is the peak current in the primary that flows
through the MOSFET at full load.
When the voltage produced by this current (through the
current-sense resistor) exceeds the current-limit com-
parator threshold, the MOSFET drivers (NDRVA/
NDRVB) quickly terminate the current on-cycle. In most
cases, a small RC filter is required to filter out the lead-
ing-edge spike on the sense waveform. Set the corner
Typically, there are two sources of noise emission in a
switching power supply: high di/dt loops and high dV/dt
surfaces. For example, traces that carry the drain cur-
rent often form high di/dt loops. Similarly, the heatsink of
the MOSFET presents a dV/dt source, thus minimize the
surface area of the heatsink as much as possible.
To achieve best performance and to avoid ground
loops, use a solid ground-plane connection.
frequency to a few MHz above the switching frequency.
Selector Guide
PART
MAX5069A
MAX5069B
MAX5069C
MAX5069D
BOOTSTRAP
UVLO
Yes
Yes
No
No
STARTUP
VOLTAGE (V)
23.6
23.6
10.8
10.8
PROGRAMMABLE
UVLO
HYSTERESIS
No
Yes
Yes
No
OSCILLATOR SYNC
Yes
No
No
Yes
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| R1D10-3.305 | CONV DC/DC 1W 3.3VIN +/-05VOUT |
| CDBMH240-HF | DIODE SCHOTTKY 40V 2.0A SOD123T |
| CDBMH230-HF | DIODE SCHOTTKY 30V 2.0A SOD123T |
| CDBMH220-HF | DIODE SCHOTTKY 20V 2.0A SOD123T |
| CDBM260-G | DIODE SCHOTTKY 60V 2.0A SOD123 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX506ACPP | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACPP+ | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACWP | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACWP+ | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX506ACWP+T | 功能描述:数模转换器- DAC 8-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。