- 您现在的位置：买卖IC网 > PDF目录14390 > MAX5098AATJ+ (Maxim Integrated Products)IC REG BUCK BST ADJ 1A/2A 32TQFN PDF资料下载
参数资料
| 型号： | MAX5098AATJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST ADJ 1A/2A 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.8 V ~ 0.85 V，4.5 V ~ 28 V |
| 输入电压： | 4.5 V ~ 19 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 200kHz ~ 2.2MHz |
| 电流 - 输出： | 1A，2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Dual, 2.2MHz, Automotive Buck or Boost
Converter with 80V Load-Dump Protection
V L
V IN
V L
V IN
V L
V+
V L
V+
OUTPUT2
DRAIN2
DRAIN1
OUTPUT1
OUTPUT2
DRAIN2
DRAIN1
OUTPUT1
SOURCE2
SOURCE1
SOURCE2
SOURCE1
MAX5098A
MAX5098A
FB2
FB1
R2
FB2
FB1
R1
V L
EN2
EN1
V L
V L
EN2
EN1
V L
PGOOD1
SEQUENCING—OUTPUT 2 DELAYED WITH RESPECT TO OUTPUT 1.
Figure 2. Power-Supply Sequencing Configurations
C2
R1/C1 AND R2/C2 ARE SIZED FOR REQUIRED SEQUENCING.
C1
PGOOD_
Converter 1 and converter 2 include a power-good flag,
PGOOD1 and PGOOD2, respectively. Since PGOOD_
is an open-drain output and can sink 3mA while provid-
ing the TTL logic-low signal, pull PGOOD_ to a logic
voltage to provide a logic-level output. PGOOD1 goes
low when converter 1’s feedback FB1 drops to 92.5%
(V TPGOOD_ ) of its nominal set point. The same is true for
converter 2. Connect PGOOD_ to SGND or leave
unconnected if not used.
Current Limit
The internal MOSFET switch current of each converter is
monitored during its on-time. When the peak switch cur-
rent crosses the current-limit threshold of 3.45A (typ) and
2.1A (typ) for converter 1 and converter 2, respectively,
the on-cycle is terminated immediately and the inductor
is allowed to discharge. The MOSFET is turned on at the
next clock pulse, initiating a new switching cycle.
In deep overload or short-circuit conditions when the
V FB_ voltage drops below 0.2V, the switching frequen-
cy is reduced to 1/4 x f SW to provide sufficient time for
the inductor to discharge. During overload conditions, if
the voltage across the inductor is not high enough to
allow for the inductor current to properly discharge,
current runaway may occur. Current runaway can
destroy the device in spite of internal thermal-overload
protection. Reducing the switching frequency during
overload conditions allows more time for inductor dis-
charge and prevents current runaway.
Output Overvoltage Protection
The MAX5098A outputs are protected from output volt-
age overshoots due to input transients and shorting the
output to a high voltage. When the output voltage rises
above the overvoltage threshold, 110% (typ) nominal
FB_, the overvoltage condition is triggered. When the
overvoltage condition is triggered on either channel,
both converters are immediately turned off, 20 Ω pull-
down switches from SOURCE_ to PGND_ are turned on
to help the output-voltage discharge, and the gate of
the load-dump protection external MOSFET is pulled
low. The device restarts as soon as both converter out-
puts discharge, bringing both FB_ input voltages below
12.5V of their nominal set points.
Thermal-Overload Protection
During continuous short circuit or overload at the out-
put, the power dissipation in the IC can exceed its limit.
The MAX5098A provides thermal shutdown protection
with temperature hysteresis. Internal thermal shutdown
is provided to avoid irreversible damage to the device.
When the die temperature exceeds +165°C (typ), an
on-chip thermal sensor shuts down the device, forcing
the internal switches to turn off, allowing the IC to cool.
The thermal sensor turns the part on again with soft-
start after the junction temperature cools by +20°C.
During thermal shutdown, both regulators shut down,
PGOOD_ goes low, and soft-start resets. The internal
20V zener clamp from IN_HIGH to SGND is not turned
off during thermal shutdown because clamping action
must be always active.
______________________________________________________________________________________
17
相关PDF资料 |
PDF描述 |
|---|---|
| RBM36DRUS | CONN EDGECARD 72POS DIP .156 SLD |
| VI-B5V-EX-F4 | CONVERTER MOD DC/DC 5.8V 75W |
| ECC35DRSD-S273 | CONN EDGECARD 70POS DIP .100 SLD |
| MAX5099ATJ+ | IC REG BUCK SYNC ADJ DL 32TQFN |
| EMM15DTMT-S189 | CONN EDGECARD 30POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5098AATJ+ | 功能描述:直流/直流开关转换器 Dual 2.2MHz Buck or Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX5098AATJ+T | 功能描述:直流/直流开关转换器 Dual 2.2MHz Buck or Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX5099 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual, 2.2MHz, Automotive Synchronous Buck Converter with 80V Load-Dump Protection |
| MAX5099ATJ | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual, 2.2MHz, Automotive Synchronous Buck Converter with 80V Load-Dump Protection |
| MAX5099ATJ+ | 功能描述:直流/直流开关转换器 Dual 2.2MHz Synch Buck Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。