- 您现在的位置：买卖IC网 > PDF目录2011 > MAX5816ATB+T (Maxim Integrated Products)IC DAC 12BIT SRL 4CH 10TDFN PDF资料下载
参数资料
| 型号： | MAX5816ATB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/32页 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT SRL 4CH 10TDFN |
| 产品培训模块： | Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 设置时间： | 4.5µs |
| 位数： | 12 |
| 数据接口： | I²C，串行 |
| 转换器数目： | 4 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 1.95W |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 4 电压，单极 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Ultra-Small, Quad-Channel, 12-Bit Buffered Output DAC
with Internal Reference and I2C Interface
MAX5816
Maxim Integrated Products 15
an open-drain output. A pullup resistor, typically 4.7kI is
required on SDA. SCL operates only as an input. A pullup
resistor, typically 4.7kI, is required on SCL if there are
multiple masters on the bus, or if the single master has
an open-drain SCL output.
Series resistors in line with SDA and SCL are optional.
Series resistors protect the digital inputs of the MAX5816
from high voltage spikes on the bus lines and mini-
mize crosstalk and undershoot of the bus signals. The
MAX5816 can accommodate bus voltages higher than
VDD up to a limit of 5.5V; bus voltages lower than VDD
are not recommended and may result in significantly
increased interface currents.
I2C START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A mas-
ter initiates communication by issuing a START condition.
A START condition is a high-to-low transition on SDA with
SCL high. A STOP condition is a low-to-high transition
on SDA while SCL is high (Figure 2). A START condition
from the master signals the beginning of a transmission
to the MAX5816. The master terminates transmission
and frees the bus, by issuing a STOP condition. The bus
remains active if a Repeated START condition is gener-
ated instead of a STOP condition.
I2C Early STOP and
Repeated START Conditions
The MAX5816 recognizes a STOP condition at any point
during data transmission except if the STOP condition
occurs in the same high pulse as a START condition.
Transmissions ending in an early STOP condition will not
impact the internal device settings. If the STOP occurs
during a readback byte, the transmission is terminated
and a later read mode request will begin transfer of the
requested register data from the beginning (this applies
to combined format I2C read mode transfers only,
interface verification mode transfers will be corrupted).
See Figure 2.
I2C Slave Address
The slave address is defined as the seven most sig-
nificant bits (MSBs) followed by the R/W bit. See
Figure 4. The five most significant bits are 00011 with the
2 LSBs determined by ADDR as shown in Table 1. Setting
the R/W bit to 1 configures the MAX5816 for read mode.
Setting the R/W bit to 0 configures the MAX5816 for write
mode. The slave address is the first byte of information
sent to the MAX5816 after the START condition.
The MAX5816 has the ability to detect an unconnected
state on the ADDR input for additional address flexibility;
if leaving the ADDR input unconnected, be certain to
minimize all loading on the pin (i.e. provide a landing for
the pin, but do not allow any board traces).
Figure 2. I2C START, Repeated START, and STOP Conditions
Table 1. I2C Slave Address LSBs for
TDFN Package
ADDR
A1
A0
VDD
0
N.C.
1
0
GND
1
SCL
SDA
SSrP
VALID START, REPEATED START, AND STOP PULSES
PS
P
SP
P
S
INVALID START/STOP PULSE PAIRINGS -ALL WILL BE RECOGNIZED AS STARTS
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5820MEUA+ | IC DAC 8BIT DUAL 2WIRE SER 8UMAX |
| MAX5821LEUA+T | IC DAC 10BIT DL 2WIRE SER 8-UMAX |
| MAX5839BCMH | IC DAC OCTAL V-OUT 13BIT 44-MQFP |
| MAX5841MEUB+T | IC DAC 10BIT QUAD 2WIRE 10-UMAX |
| MAX5851ETL+T | IC DAC 8BIT DUAL 80MSPS 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5820LEUA | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820LEUA+ | 功能描述:数模转换器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820LEUA+T | 功能描述:数模转换器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820LEUA-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820MEUA | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。