- 您现在的位置：买卖IC网 > PDF目录2011 > MAX5895EGK+D (Maxim Integrated Products)IC DAC 16BIT 500MSPS DUAL 68-QFN PDF资料下载
参数资料
| 型号： | MAX5895EGK+D |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/31页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT 500MSPS DUAL 68-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 30 |
| 设置时间： | 11ns |
| 位数： | 16 |
| 数据接口： | 并联 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 511mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 68-VFQFN 裸露焊盘 |
| 供应商设备封装： | 68-QFN 裸露焊盘（10x10） |
| 包装： | 管件 |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 500M |
| 产品目录页面： | 1398 (CN2011-ZH PDF) |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX5895
16-Bit, 500Msps Interpolating and Modulating
Dual DAC with CMOS Inputs
12
______________________________________________________________________________________
Detailed Description
The MAX5895 dual, 500Msps, high-speed, 16-bit, cur-
rent-output DAC provides superior performance in
communication systems requiring low-distortion ana-
log-signal reconstruction. The MAX5895 combines two
DAC cores with 8x/4x/2x/1x programmable digital inter-
polation filters, a digital quadrature modulator, an SPI-
compatible serial interface for programming the device,
and an on-chip 1.20V reference. The full-scale output
current range is programmable from 2mA to 20mA to
optimize power dissipation and gain control.
Each channel contains three selectable interpolating fil-
ters making the MAX5895 capable of 1x, 2x, 4x, or 8x
interpolation, which allows for low-input and high-out-
put data rates. When operating in 8x interpolation
mode, the interpolator increases the DAC conversion
rate by a factor of eight, providing an eight-fold
increase in separation between the reconstructed
waveform spectrum and its first image. The MAX5895
accepts either two’s complement or offset binary input
data format and can operate from either a single- or
dual-port input bus.
The MAX5895 includes modulation modes at fIM/2 and
fIM/4, where fIM is the data rate at the input of the modula-
tor. If 2x interpolation is used, this data rate is 2x the input
data rate. If 4x or 8x interpolation is used, this data rate is
4x the input data rate. Table 1 summarizes the modulator
operating data rates for dual-port mode.
The power-down modes can be used to turn off each
DAC’s output current or the entire digital section.
Programming both DACs into power-down simultane-
ously will automatically power down the digital interpo-
lator filters. Note the SPI section is always active.
The analog and digital sections of the MAX5895 have
separate power-supply inputs (AVDD3.3, AVDD1.8,
AVCLK, DVDD3.3, and DVDD1.8), which minimize noise
coupling from one supply to the other. AVDD1.8 and
DVDD1.8 operate from a typical 1.8V supply, and all
other supply inputs operate from a typical 3.3V supply.
Serial Interface
The SPI-compatible serial interface programs the
MAX5895 registers. The serial interface consists of the
CS, SDI, SCLK, and SDO. Data is shifted into SDI on
the rising edge of the SCLK when CS is low. When CS
is high, data presented at SDI is ignored and SDO is in
high-impedance mode. Note:
CS must transition high
after each read/write operation. SDO is the serial data
output for reading registers to facilitate easy debug-
ging during development. SDI and SDO can be con-
nected together to form a 3-wire serial interface bus or
remain separate and form a 4-wire SPI bus.
The serial interface supports two-byte transfer in a
communication cycle. The first byte is a control byte
written to the MAX5895 only. The second byte is a data
byte and can be written to or read from the MAX5895.
Table 1. Quadrature Modulator Operating Data Rates (fIM is the Data Rate at the Input of
the Modulator) for Dual-Port Mode
INTERPOLATION RATE
MODULATION MODE (fLO)
MODULATION FREQUENCY
RELATIVE TO fDAC
MODULATION FREQUENCY
RELATIVE TO fDATA
fIM/2
fDAC/2
fDATA/2
1x
fIM/4
fDAC/4
fDATA/4
fIM/2
fDAC/2
fDATA
2x
fIM/4
fDAC/4
fDATA/2
fIM/2
fDAC/2
2 x fDATA
4x
fIM/4
fDAC/4
fDATA
fIM/2
fDAC/4
2 x fDATA
8x
fIM/4
fDAC/8
fDATA
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5898EGK+D | IC DAC 16BIT DUAL 500MSPS 68-QFN |
| MAX6900ETT+T | IC RTC I2C COMPAT 6-TDFN |
| MAX6902ETA+T | IC RTC SPI COMPAT 8-TDFN |
| MAX7375AXR604+T | IC OSC SILICON SC70-3 |
| MAX7394ATTLY+T | IC OSC SILICON 922KHZ 6-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5895EGK-TD | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5895EVCMOD2 | 功能描述:数模转换器- DAC Evaluation Kit for the MAX5893/MAX5894/MAX5895 RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5895EVKIT | 功能描述:数模转换器- DAC Evaluation Kit for the MAX5893/MAX5894/MAX5895 RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5898EGK+D | 功能描述:数模转换器- DAC 16-Bit 2Ch 500Msps DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5898EGK+TD | 功能描述:数模转换器- DAC 16-Bit 2Ch 500Msps DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。