- 您现在的位置：买卖IC网 > Datasheet目录43 > MAX5932ESA+T (Maxim Integrated)IC HOT-SWAP CONTROLLER 8-SOIC Datasheet资料下载
参数资料
| 型号： | MAX5932ESA+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/15页 |
| 文件大小： | 247K |
| 描述： | IC HOT-SWAP CONTROLLER 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 9 V ~ 80 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
Positive High-Voltage, Hot-Swap Controller
______________________________________________________________________________________ 11
TIMER
TIMER provides a method for programming the maxi-
mum time the device is allowed to operate in current
limit. When the current-limit circuitry is not active,
TIMER is pulled to GND by a 3礎 current source. After
the current-limit circuit becomes active, an 80礎 pullup
current source is connected to TIMER and the voltage
rises with a slope equal to 77礎/C
TIMER
as long as the
current-limit circuit remains active. Once the desired
maximum current-limit time is chosen, the capacitor
value is calculated using the following equations:
C(nF) = 65 x t(ms)
or
T
LIMIT
= (C
TIMER
/80礎) x 1.233V
When the current-limit circuit turns off, TIMER is dis-
charged to GND by the 3礎 current source.
Whenever TIMER reaches 1.233V, the internal fault
latch is set. GATE is immediately pulled to GND and
TIMER is pulled back to GND by the 3礎 current
source. When TIMER falls below 0.5V, ON is pulsed low
to reset the internal fault latch.
The waveform in Figure 9 shows how the output latches
off following a short circuit. The drop across the sense
resistor is held at 12mV as the timer ramps up. Since
the output did not rise, FB remains below 0.5V and the
circuit latches off. For Figure 9, C
T
= 100nF.
Undervoltage and Overvoltage Detection
ON can be used to detect an undervoltage condition at
the power-supply input. ON is internally connected to
an analog comparator with 80mV of hysteresis. If ON
falls below its threshold voltage (1.233V), GATE is
pulled low and is held low until ON is high again.
Figure 10 shows an overvoltage detection circuit. When
the input voltage exceeds the Zener diodes breakdown
voltage, D1 turns on and starts to pull TIMER high. After
TIMER is pulled higher than 1.233V, the fault latch is set
and GATE is pulled to GND immediately, turning off
transistor Q1 (see Figure 11). Operation is restored
either by interrupting power or by pulsing ON low.
Power-Good Detection
The MAX5932 includes a comparator for monitoring the
output voltage. The noninverting input (FB) is com-
pared against an internal 1.233V precision reference
and exhibits 80mV hysteresis. The comparators output
(PWRGD) is an open drain one capable of operating
from a pullup as high as 80V.
The PWRGD can be used to directly enable/disable a
power module with an active-high enable input. Figure
12 shows how to use PWRGD to control an active-low
enable-input power module. Signal inversion is accom-
plished by transistor Q2 and R7 or use MAX5933.
Supply Transient Protection
The MAX5932 is 100% tested and guaranteed to be
safe from damage with supply voltages up to 80V.
However, spikes above 85V may damage the device.
During a short-circuit condition, the large change in
currents flowing through the power-supply traces can
cause inductive voltage spikes that could exceed 85V.
To minimize the spikes, the power-trace parasitic
inductance should be minimized by using wider traces
or heavier trace plating and a 0.1礔 bypass capacitor
placed between V
CC
and GND. A transient voltage
suppressor (TVS) at the input can also prevent damage
from voltage surges.
RESPONSE TIME TO OVERCURRENT
V
CC
- V
SENSE
(mV)
200
100
2
4
6
8
10
12
14
0
0
300
Figure 8. Response Time to Overcurrent
SHORT-CIRCUIT WAVEFORMS
I
SENSE
1A/div
TIMER
1V/div
OUTPUT
50V/div
GATE
50V/div
10ms/div
Figure 9. Short-Circuit Waveforms
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5933EESA+ | IC HOT-SWAP CONTROLLER 8-SOIC |
| MAX5934EEE+ | IC HOT-SWAP CONTROLLER 16-QSOP |
| MAX5935EAX+ | IC CTRLR POWER QUAD 36-SSOP |
| MAX5937LCESA+ | IC HOT-SWAP CTRLR -48V 8-SOIC |
| MAX5938LEEE+ | IC HOT-SWAP CTRLR -48V 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5932ESA-TG077 | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5932EVKIT | 功能描述:热插拔功率分布 Evaluation Kit for the MAX5932 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5933AESA | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5933AESA+ | 功能描述:热插拔功率分布 Positive Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5933AESA+T | 功能描述:热插拔功率分布 Positive Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。