- 您现在的位置：买卖IC网 > PDF目录11561 > MAX5945CAX+T (Maxim Integrated Products)IC NETWORK PWR CTRL 36-SSOP PDF资料下载
参数资料
| 型号： | MAX5945CAX+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/44页 |
| 文件大小： | 0K |
| 描述： | IC NETWORK PWR CTRL 36-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 控制器类型： | 网络电源控制器 |
| 接口： | I²C |
| 电源电压： | 3.3V |
| 电流 - 电源： | 4.2mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
agement where it detects a PD that draws more current
than the allowable amount for its class. The MAX5945’s
extensive programmability enhances system flexibility
and allows for uses in other applications.
The MAX5945 has four different operating modes: auto
mode, semi-auto mode, manual mode, and shutdown
mode (see the Operation Modes section). A special
watchdog feature allows the hardware to gracefully
take over control if the software/firmware crashes. A
cadence timing feature allows the MAX5945 to be used
in midspan systems.
The MAX5945 provides input undervoltage lockout,
input undervoltage detection, input overvoltage lockout,
overtemperature protection, output-voltage slew-rate
limit during startup, power-good status, and fault
status. The MAX5945’s programmability includes
gate-charging current, current-limit threshold, startup
timeout, overcurrent timeout, autorestart duty cycle, PD
disconnect AC detection threshold and PD disconnect
detection timeout.
The MAX5945 communicates with the system
microcontroller through an I2C-compatible interface.
The MAX5945 features separate input and output data
lines (SDAIN and SDAOUT) for use with optocoupler
isolation. The MAX5945 is a slave device. Its four
address inputs allow 16 unique MAX5945 addresses. A
separate INT output and four independent shutdown
inputs (SHD_) allow fast interrupt signals between the
MAX5945 and the microcontroller. A RESET input
allows hardware reset of the device.
Reset
Reset is a condition the MAX5945 enters after any of
the following conditions:
After power-up (VEE and VDD rise above their UVLO
thresholds).
Hardware reset. The RESET input is driven low and
up high again any time after power-up.
Software reset. Writing a 1 into R1Ah[4] any time
after power-up.
Thermal shutdown.
During a reset, the MAX5945 resets its register map to
the reset state as shown in Table 30 and latches in the
state of AUTO (pin 35) and MIDSPAN (pin 2). During
normal operation, changes at the AUTO and MIDSPAN
inputs are ignored. While the condition that caused the
reset persists (i.e., high temperature, RESET input low,
or UVLO conditions) the MAX5945 will not acknowl-
edge any addressing from the serial interface.
Port Reset (R1Ah[3:0])
Set high anytime during normal operation to turn off
power and clear the events and status registers of the
corresponding port. Port reset only resets the events
and status registers.
Operation Modes
The MAX5945 contains four independent but identical
state machines to provide reliable and real-time control
of the four network ports. Each state machine has four
different operating modes: auto, semi-auto, manual,
and shutdown. Auto mode allows the device to operate
automatically without any software supervision. Semi-
auto mode, upon request, continuously detects and
classifies a device connected to a port but does not
power up that port until instructed by software. Manual
mode allows total software control of the device and is
useful in system diagnostic. Shutdown mode terminates
all activities and securely turns off power to the ports.
Switching between AUTO, SEMI, or MANUAL mode
does not take effect until the part finishes its current
task. When the port is set into SHUTDOWN mode, all
the port operations are immediately stopped and the
port remains idle until SHUTDOWN is exited.
Automatic (AUTO) Mode
Enter automatic (AUTO) mode by forcing the
AUTO input high prior to a reset, or by setting
R12h[P_ M1,P_M0] to [1,1] during normal operation
(see Tables 15 and 15a). In AUTO mode, the MAX5945
performs detection, classification, and powers up the
port automatically once a valid PD is detected at the
port. If a valid PD is not detected at the port, the
MAX5945 repeats the detection routine continuously
until a valid PD is detected.
Going into AUTO mode, the DET_EN and CLASS_EN
bits are set to high and stay high unless changed by
software. Using software to set DET_EN and/or
CLASS_EN low causes the MAX5945 to skip detection
and/or classification. As a protection, disabling the
detection routine in AUTO mode will not allow the corre-
sponding port to power up, unless the DET_BYP
(R23H[4]) is set to 1.
The AUTO status is latched into the register only during
a reset. Any changes to the AUTO input after reset is
ignored.
Semi-Automatic (SEMI) Mode
Enter semi-automatic (SEMI) mode by setting
R12h[P_M1,P_M0] to [1,0] during normal operation
(see Tables 15 and 15a). In SEMI mode, the MAX5945,
upon request, performs detection and/or classification
repeatedly but does not power up the port(s), regard-
less of the status of the port connection.
MAX5945
Quad Network Power Controller
for Power-Over-LAN
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| VE-253-IX-S | CONVERTER MOD DC/DC 24V 75W |
| VE-2TX-IX-S | CONVERTER MOD DC/DC 5.2V 75W |
| VE-2TV-IX-S | CONVERTER MOD DC/DC 5.8V 75W |
| PIC16LF1783-E/ML | IC MCU 8BIT 7KB FLASH 28-QFN |
| PIC16LF1782-E/SP | IC MCU 8BIT 3.5KB FLASH 28-SPDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5945EAX | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5945EAX+ | 功能描述:热插拔功率分布 IEEE 802.3af Quad Net Pwr Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5945EAX+T | 功能描述:热插拔功率分布 IEEE 802.3af Quad Net Pwr Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5945EAX-T | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5945EVKIT | 功能描述:电源管理IC开发工具 Evaluation Kit/Evaluation System for the MAX5945 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。