- 您现在的位置：买卖IC网 > PDF目录180478 > MAX5965BEAX+ (MAXIM INTEGRATED PRODUCTS INC) High-Power, Quad, Monolithic, PSE Controllers for Power over Ethernet; Package: SSOP;36 pin;163 mm² ; Temperature: -40°C to +85°C PDF资料下载
参数资料
| 型号： | MAX5965BEAX+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | High-Power, Quad, Monolithic, PSE Controllers for Power over Ethernet; Package: SSOP;36 pin;163 mm² ; Temperature: -40°C to +85°C |
| 中文描述： | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| 封装： | ROHS COMPLIANT, SSOP-36 |
| 文件页数： | 11/54页 |
| 文件大小： | 1525K |
| 代理商： | MAX5965BEAX+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
MAX5965A/MAX5965B
High-Power, Quad, Monolithic, PSE Controllers
for Power over Ethernet
______________________________________________________________________________________
19
Powered Device Classification
(PD Classification)
During the PD classification mode, the MAX5965A/
MAX5965B force a probe voltage (-18V) at DET_ and
measure the current into DET_. The measured current
determines the class of the PD.
After each classification cycle, the device sets the
CL_END_ bit (R04h/05h[7:4]) high and reports the clas-
sification results in the status registers R0Ch[6:4],
R0Dh[6:4], R0Eh[6:4], and R0Fh[6:4]. The CL_END_ bit
is reset to low when read through register R05h or after
a port reset. Both events registers, R04h, and R05h are
cleared after the port powers down. Table 2 shows the
IEEE 802.3af requirement for a PSE classifying a PD at
the power interface (PI).
The MAX5965A/MAX5965B support high power beyond
the IEEE 802.3af standard by providing additional clas-
sifications (Class 5 and 2-event classification).
Class 5 PD Classification
During classification, if the MAX5965A/MAX5965B
detect currents in excess of ICLASS > 48mA, then the
PD will be classified as a Class 5 powered device.
Status registers R0Ch[6:4] or R0Dh[6:4] or R0Eh[6:4] or
R0Fh[6:4] will report the Class 5 classification result.
2-Event (Class 6) PD Classification
When 2-event classification is activated, the classifica-
tion cycle is repeated three times with 8ms wait time
between each cycle (see Figure 1b). Between each
classification cycle, the MAX5965A/MAX5965B do not
reset the port voltage completely but keeps the output
voltage at -9V. The EN_CL6 bits in R1Ch[7:4] enable 2-
event classification on a per port basis.
Powered State
When the MAX5965A/MAX5965B enter a powered
state, the tSTART and tDISC timers are reset. Before
turning on the port power, the MAX5965A/MAX5965B
check if any other port is not turning on and if the
tFAULT timer is zero. Another check is performed if the
ACD_EN_ bit is set, in this case the OSC_FAIL bit must
be low (oscillator is okay) for the port to be powered.
If these conditions are met, the MAX5965A/MAX5965B
enter startup where it turns on power to the port. An
internal signal, POK_, asserts high when VOUT_ is within
2V from VEE. PGOOD_ status bits are set high if POK_
stays high longer than tPGOOD. PGOOD_ immediately
resets when POK_ goes low (see Figure 2).
The PG_CHG_ bit sets when a port powers up or down.
PWR_EN_ sets when a port powers up and resets when
a port shuts down. The port shutdown timer lasts 0.5ms
and prevents other ports from turning off during that peri-
od, except in the case of emergency shutdowns (RESET
= L, RESET_IC = H, VEEUVLO, VDDUVLO, and TSHD).
The MAX5965A/MAX5965B always check the status of
all ports before turning off. A priority logic system deter-
mines the order to prevent the simultaneous turn-on or
turn-off of the ports. The port with the lesser ordinal
number gets priority over the others (i.e., port 1 turns on
first, port 2 second, port 3 third, and port 4 fourth).
Setting PWR_OFF_ high turns off power to the corre-
sponding port.
Table 2. PSE Classification of a PD (Refer to Table 33-4 of the IEEE 802.3af)
MEASURED ICLASS (mA)
CLASSIFICATION
0 to 5
Class 0
> 5 and < 8
May be Class 0 and 1
8 to 13
Class 1
> 13 and < 16
May be Class 1 or 2
16 to 21
Class 2
> 21 and < 25
May be Class 2 or 3
25 to 31
Class 3
> 31 and < 35
May be Class 3 or 4
35 to 45
Class 4
> 45 and < 51
May be Class 4 or 5
51 to 68
Class 5
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5965BUAX+ | High-Power, Quad, Monolithic, PSE Controllers for Power over Ethernet; Package: SSOP;36 pin;163 mm² ; Temperature: 0°C to +85°C |
| MAX6317HUK25AW-T | Versatile Customizable SOT Reset + Watchdog ICs Offer 3224 Unique Options[Japanese] |
| MAX6317HUK25AX-T | Versatile Customizable SOT Reset + Watchdog ICs Offer 3224 Unique Options |
| MAX6317HUK25AY-T | Versatile Customizable SOT Reset + Watchdog ICs Offer 3224 Unique Options[Japanese] |
| MAX6317HUK25AZ-T | Versatile Customizable SOT Reset + Watchdog ICs Offer 3224 Unique Options |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5965BEAX+ | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5965BEAX+T | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5965BUAX+ | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5965BUAX+T | 功能描述:热插拔功率分布 Quad PSE Controller for POE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5967BETG+ | 功能描述:热插拔功率分布 I2C Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。