- 您现在的位置：买卖IC网 > PDF目录15515 > MAX608ESA+ (Maxim Integrated Products)IC REG CTRLR BST PWM 8-SOIC PDF资料下载
参数资料
| 型号： | MAX608ESA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 300kHz |
| 占空比： | 85% |
| 电源电压： | 1.8 V ~ 16.5 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1408 (CN2011-ZH PDF) |
5V or Adjustable, Low-Voltage,
Step-Up DC-DC Controller
Power Transistor Selection
Use an N-channel MOSFET power transistor with the
MAX608.
Use logic-level or low-threshold N-FETs to ensure the
external N-channel MOSFET (N-FET) is turned on com-
pletely and that start-up occurs. N-FETs provide the
highest efficiency because they do not draw any DC
gate-drive current.
When selecting an N-FET, some important parameters
to consider are the total gate charge (Q g ), on-resis-
tance (r DS(ON) ), reverse transfer capacitance (C RSS ),
maximum drain to source voltage (V DS max), maximum
gate to source voltage (V GS max), and minimum thresh-
old voltage (V TH min).
Q g takes into account all capacitances associated with
charging the gate. Use the typical Q g value for best
results; the maximum value is usually grossly over-
specified since it is a guaranteed limit and not the mea-
sured value. The typical total gate charge should be
50nC or less. With larger numbers, the EXT pins may
not be able to adequately drive the gate. The EXT
rise/fall time varies with different capacitive loads as
shown in the Typical Operating Characteristics.
The two most significant losses contributing to the
N-FET’s power dissipation are I 2 R losses and switching
losses. Select a transistor with low r DS(ON) and low
C RSS to minimize these losses.
Determine the maximum required gate-drive current
from the Q g specification in the N-FET data sheet.
Select an N-FET with a BV DSS > V OUT , BV GSS > V OUT ,
and a minimum V TH of 0.5V below the minimum input
voltage.
When using a power supply that decays with time
(such as a battery), the N-FET transistor will operate in
its linear region when the voltage at EXT approaches
the threshold voltage of the FET, dissipating excessive
power. Prolonged operation in this mode may damage
the FET. To avoid this condition, make sure V EXT is
above the V TH of the FET, or use a voltage detector
(such as the MAX8211) to put the IC in shutdown mode
once the input supply voltage falls below a predeter-
mined minimum value. Excessive loads with low input
voltages can also cause this condition.
The MAX608’s maximum allowed switching frequency
during normal operation is 300kHz. However, at start-
up, the maximum frequency can be 500kHz, so the
maximum current required to charge the N-FET’s gate
is f(max) x Q g (typ). Use the typical Q g number from the
transistor data sheet. For example, the MMFT3055EL
has a Q g (typ) of 7nC (at V GS = 5V), therefore the cur-
rent required to charge the gate is:
I GATE (max) = (500kHz) (7nC) = 3.5mA.
Figure 2a’s application circuit uses a 4-pin MMFT3055EL
surface-mount N-FET that has 150m ? on-resistance with
4.5V V GS , and a guaranteed V TH of less than 2V. Figure
2c’s application circuit uses an Si6426DQ logic-level N-
FET with a threshold voltage (V TH ) of 1V.
Diode Selection
The MAX608’s high switching frequency demands a
high-speed rectifier. Schottky diodes such as the
1N5817 –1N5822 are recommended. Make sure the
Schottky diode’s average current rating exceeds the
peak current limit set by R SENSE , and that its break-
down voltage exceeds V OUT . For high-temperature
applications, Schottky diodes may be inadequate due
to their high leakage currents; high-speed silicon
diodes such as the MUR105 or EC11FS1 can be used
instead. At heavy loads and high temperatures, the
benefits of a Schottky diode’s low forward voltage may
outweigh the disadvantage of high leakage current.
Capacitor Selection
Output Filter Capacitor
The primary criterion for selecting the output filter capac-
itor (C4) is low effective series resistance (ESR). The
product of the peak inductor current and the output filter
capacitor’s ESR determines the amplitude of the ripple
seen on the output voltage. Two OS-CON 100μF, 16V
output filter capacitors in parallel with 35m ? of ESR each
typically provide 75mV ripple when stepping up from 2V
to 5V at 500mA (Figure 2a). Smaller-value and/or higher-
ESR capacitors are acceptable for light loads or in appli-
cations that can tolerate higher output ripple.
Since the output filter capacitor’s ESR affects efficien-
cy, use low-ESR capacitors for best performance. See
Table 1 for component selection.
Input Bypass Capacitors
The input bypass capacitor (C1) reduces peak currents
drawn from the voltage source and also reduces noise
caused by the switching action of the MAX608 at the
voltage source. The input voltage source impedance
determines the size of the capacitor required at the
OUT input. As with the output filter capacitor, a low-ESR
capacitor is recommended. For output currents up to
1A, 150μF (C1) is adequate, although smaller bypass
capacitors may also be acceptable.
Bypass the IC with a 0.1μF ceramic capacitor (C2)
placed as close as possible to the OUT and GND pins.
Reference Capacitor
Bypass REF with a 0.1μF capacitor (C3). REF can
source up to 100μA of current for external loads.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| S4924-824K | INDUCTOR SHIELDED 820.0UH SMD |
| UPM1V391MHD6 | CAP ALUM 390UF 35V 20% RADIAL |
| UPJ2G4R7MHD1TO | CAP ALUM 4.7UF 400V 20% RADIAL |
| UVP1H101MPD | CAP ALUM 100UF 50V 20% RADIAL |
| MAX1649CSA+ | IC REG CTRLR BUCK PWM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX608ESA+ | 功能描述:DC/DC 开关控制器 5V or Adjustable Step-Up DC/DC Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX608ESA+T | 功能描述:DC/DC 开关控制器 5V or Adjustable Step-Up DC/DC Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX608ESA-T | 功能描述:DC/DC 开关控制器 5V or Adjustable Step-Up DC/DC Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX608EVKIT | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Evaluation Kit for the MAX608 |
| MAX608EVKIT-SO | 功能描述:DC/DC 开关控制器 5V or Adjustable Low-Voltage Step-Up DC-DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。