- 您现在的位置：买卖IC网 > PDF目录15515 > MAX608ESA+ (Maxim Integrated Products)IC REG CTRLR BST PWM 8-SOIC PDF资料下载
参数资料
| 型号： | MAX608ESA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 300kHz |
| 占空比： | 85% |
| 电源电压： | 1.8 V ~ 16.5 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1408 (CN2011-ZH PDF) |
5V or Adjustable, Low-Voltage,
Step-Up DC-DC Controller
Unlike traditional PFM converters, the MAX608 uses a
sense resistor to control the peak inductor current. The
device also operates with high switching frequencies
(up to 300kHz), allowing the use of miniature external
FB
R2
V OUT
components.
As with traditional PFM converters, the power transistor
MAX608
R1
C5*
is not turned on until the voltage comparator senses
the output is out of regulation. However, unlike tradition-
al PFM converters, the MAX608 switch uses the combi-
nation of a peak current limit and a pair of one-shots
R1 = 10k TO 500k
( V OUT -1 )
that set the maximum on-time (16μs) and minimum off-
time (2.3μs); there is no oscillator. Once off, the mini-
GND
R2 = R1
V
REF
(
)
V OUT
mum off-time one-shot holds the switch off for 2.3μs.
After this minimum time, the switch either 1) stays off if
the output is in regulation, or 2) turns on again if the
output is out of regulation.
The control circuitry allows the IC to operate in continu-
ous-conduction mode (CCM) while maintaining high
efficiency with heavy loads. When the power switch is
turned on, it stays on until either 1) the maximum on-
time one-shot turns it off (typically 16μs later), or 2) the
switch current reaches the peak current limit set by the
current-sense resistor.
The MAX608 switching frequency is variable (depend-
ing on load current and input voltage), causing variable
switching noise. However, the subharmonic noise gen-
erated does not exceed the peak current limit times the
filter capacitor equivalent series resistance (ESR). For
example, when generating a 5V output at 500mA from
a 2V input, only 75mV of output ripple occurs, using the
circuit of Figure 2a.
Low-Voltage Start-Up Oscillator
The MAX608 features a low input voltage start-up oscil-
lator that guarantees start-up with no load for input volt-
ages down to 1.8V. At these low voltages, the output
voltage is not large enough for proper error-comparator
operation and internal biasing. The start-up oscillator
has a fixed 50% duty cycle and the MAX608 disregards
the error-comparator output when the output voltage is
less than 2.5V. Above 2.5V, the error-comparator and
normal one-shot timing circuitry are used.
Shutdown Mode
When SHDN is high, the MAX608 enters shutdown
mode. In this mode, the internal biasing circuitry is
turned off (including the reference), and V OUT falls to
a diode drop below V IN (due to the DC path from the
input to the output). In shutdown mode, the supply
current drops to less than 5μA. SHDN is a TTL/CMOS
logic-level input. Connect SHDN to GND for normal
operation.
V REF = 1.5V
* OPTIONAL, SEE TEXT FOR VALUE
Figure 3. Adjustable Output Circuit
__________________Design Procedure
Setting the Output Voltage
The MAX608’s output voltage is preset to 5V (FB = 0V),
or it can be adjusted from 16.5V down to 3V using exter-
nal resistors R1 and R2, configured as shown in Figure 3.
For adjustable-output operation, select feedback resistor
R1 in the 10k ? to 500k ? range. R2 is given by:
R2 = (R1) ––––– -1
V REF
where V REF equals 1.5V.
OUT must always be connected to the circuit output.
Figure 2 shows various circuit configurations for preset/
adjustable operation.
Determining R SENSE
Use the theoretical output current curves shown in
Figures 4a –4d to select R SENSE . They are derived
using the minimum (worst-case) current-limit compara-
tor threshold value over the extended temperature
range (-40°C to +85°C). No tolerance was included for
R SENSE . The voltage drop across the diode is assumed
to be 0.5V, and the drop across the power switch
r DS(ON) and coil resistance is assumed to be 0.3V.
Determining the Inductor (L)
Practical inductor values range from 10μH to 300μH.
22μH is a good choice for most applications. In appli-
cations with large input/output differentials, the IC’s out-
put-current capability will be much less when the induc-
tance value is too low, because the IC will always operate
in discontinuous mode. If the inductor value is too low, the
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| S4924-824K | INDUCTOR SHIELDED 820.0UH SMD |
| UPM1V391MHD6 | CAP ALUM 390UF 35V 20% RADIAL |
| UPJ2G4R7MHD1TO | CAP ALUM 4.7UF 400V 20% RADIAL |
| UVP1H101MPD | CAP ALUM 100UF 50V 20% RADIAL |
| MAX1649CSA+ | IC REG CTRLR BUCK PWM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX608ESA+ | 功能描述:DC/DC 开关控制器 5V or Adjustable Step-Up DC/DC Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX608ESA+T | 功能描述:DC/DC 开关控制器 5V or Adjustable Step-Up DC/DC Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX608ESA-T | 功能描述:DC/DC 开关控制器 5V or Adjustable Step-Up DC/DC Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX608EVKIT | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Evaluation Kit for the MAX608 |
| MAX608EVKIT-SO | 功能描述:DC/DC 开关控制器 5V or Adjustable Low-Voltage Step-Up DC-DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。