参数资料
| 型号： | MAX6373KA-T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC WATCHDOG TIMER SOT23-8 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 监视器电路 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 剪切带 (CT) |
| 其它名称： | MAX6373KA-TCT |
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Output
The MAX6369/MAX6371/MAX6373 have an active-low,
open-drain output that provides a watchdog output
START
SET WDI
HIGH
PROGRAM
CODE
pulse of 100ms. This output structure sinks current
when WDO is asserted. Connect a pullup resistor from
WDO to any supply voltage up to +5.5V.
Select a resistor value large enough to register a logic
low (see Electrical Characteristics), and small enough
to register a logic high while supplying all input current
and leakage paths connected to the WDO line. A 10k Ω
pullup is sufficient in most applications. The MAX6370/
SUBROUTINE OR
PROGRAM LOOP
SET WDI LOW
RETURN
POSSIBLE
INFINITE LOOP PATH
MAX6372/MAX6374 have push-pull outputs that pro-
vide an active-low watchdog output pulse of 1ms.
When WDO deasserts, timing begins again at the
beginning of the watchdog timeout period (Figure 2).
Usage in Noisy Environments
If using the watchdog timer in an electrically noisy envi-
ronment, a bypass capacitor of 0.1μF should be con-
nected between V CC and GND as close to the device
as possible, and no further away than 0.2 inches.
Figure 4. Watchdog Flow Diagram
Selecting 011 (SET2 = 0, SET1 = 1, SET0 = 1) disables
the watchdog timer function on all devices in the family.
Operation can be reenabled without powering down by
changing the set inputs to the new desired setting. The
device assumes the new selected timing characteris-
tics and enter the startup phase after the 300μs setup
time elapses (Figure 3). WDO is high when the watch-
dog timer is disabled.
The MAX6373/MAX6374 offer a first-edge feature. In
first-edge mode (settings 101 or 110, Table 1), the
internal timer does not control the startup delay period.
Instead, startup terminates when WDI sees a transition.
If changing to first-edge mode while the device is oper-
ating, disable mode must be entered first. It is then safe
to select first-edge mode. Entering disable mode first
ensures the output is unasserted when selecting first-
edge mode and removes the danger of WDI being
masked out.
8
________________Watchdog Software
Considerations
To help the watchdog timer monitor software execution
more closely, set and reset the watchdog input at differ-
ent points in the program, rather than pulsing the watch-
dog input high-low-high or low-high-low. This technique
avoids a stuck loop, in which the watchdog timer would
continue to be reset inside the loop, keeping the watch-
dog from timing out. Figure 4 shows an example of a
flow diagram where the I/O driving the watchdog input is
set high at the beginning of the program, set low at the
end of every subroutine or loop, then set high again
when the program returns to the beginning. If the pro-
gram should hang in any subroutine, the problem would
be quickly corrected, since the I/O is continually set low
and the watchdog timer is allowed to time out, causing
WDO to pulse.
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6378XR35-T | IC VOLT DETECTOR LP 3.50V SC70-3 |
| MAX637ACSA | IC REG INV -15V/ADJ 50MA 8SOIC |
| MAX638ACSA | IC REG BUCK 5V/ADJ 75MA 8SOIC |
| MAX6392KA29+T | IC SUPERVISOR MPU DL SOT23-8 |
| MAX6394US300D4+T | IC MPU/RESET CIRC 3.0V SOT143-4 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6374KA | 制造商:Maxim Integrated Products 功能描述:8-SOT_ - Rail/Tube |
| MAX6374KA/V+T | 功能描述:计时器和支持产品 Pin-Selectable Watchdog Timer RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| MAX6374KA+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 8UA 8PIN SOT-23 - Rail/Tube |
| MAX6374KA+T | 功能描述:监控电路 Pin-Selectable Watchdog Timer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6374KA-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。