- 您现在的位置：买卖IC网 > PDF目录19601 > MAX6622UE9A+ (Maxim Integrated)IC PREC TEMP MONITOR 5CH 16TSSOP PDF资料下载
参数资料
| 型号： | MAX6622UE9A+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/18页 |
| 文件大小： | 196K |
| 描述： | IC PREC TEMP MONITOR 5CH 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C，外部传感器 |
| 精确度： | -0.1°C 本地，±3°C 远程 |
| 拓扑： | ADC，缓冲器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
Detailed Description
The MAX6622 is a precision multichannel temperature
monitor that features one local and four remote temper-
ature-sensing channels with a programmable alert
threshold for each temperature channel and a program-
mable overtemperature threshold for channels 1 and 4
(see Figure 1). Communication with the MAX6622 is
achieved through the SMBus serial interface and a
dedicated alert output. The alarm outputs, OVERT and
ALERT, assert if the software-programmed temperature
thresholds are exceeded. ALERT typically serves as an
interrupt, while OVERT can be connected to a fan, sys-
tem shutdown, or other thermal-management circuitry.
ADC Conversion Sequence
In the default conversion mode, the MAX6622 starts the
conversion sequence by measuring the temperature on
channel 1, followed by 2, 3, local channel, and 4. The
conversion result for each active channel is stored in
the corresponding temperature data register.
In some systems, one of the remote thermal diodes may
be monitoring a location that experiences temperature
changes that occur much more rapidly than in the other
channels. If faster temperature changes must be moni-
tored in one of the temperature channels, the MAX6622
allows channel 1 to be monitored at a faster rate than
the other channels. In this mode (set by writing a 1 to
bit 4 of the configuration 1 register), measurements of
channel 1 alternate with measurements of the other
channels. The sequence becomes channel 1, channel
2, channel 1, channel 3, channel 1, etc. Note that the
time required to measure all five channels is consider-
ably greater in this mode than in the default mode.
Low-Power Standby Mode
Enter software standby mode by setting the STOP bit to
1 in the configuration 1 register. Enter hardware standby
by pulling STBY low. Software standby mode disables
the ADC and reduces the supply current to approximate-
ly 30礎. Hardware standby mode halts the ADC clock,
but the supply current is approximately 350礎. During
either software or hardware standby, data is retained in
memory, and the SMBus interface is active and listening
for SMBus commands. The timeout is enabled if a
START condition is recognized on SMBus. Activity on the
SMBus causes the supply current to increase. If a stand-
by command is received while a conversion is in
progress, the conversion cycle is interrupted, and the
temperature registers are not updated. The previous
data is not changed and remains available.
5-Channel Precision Temperature Monitor
6 _______________________________________________________________________________________
PIN
NAME
FUNCTION
7
DXP4
Combined Current Source and A/D Positive Input for Channel 4 Remote Diode. Connect to the anode
of a remote-diode-connected temperature-sensing transistor. Leave unconnected or connect to V
CC
if
no remote diode is used. Place a 2200pF capacitor between DXP4 and DXN4 for noise filtering.
8
DXN4
Cathode Input for Channel 4 Remote Diode. Connect the cathode of the channel 4 remote-diode-
connected transistor to DXN4.
9
STBY
Standby Input. Drive STBY logic-low to place the MAX6622 in hardware standby mode, or logic-high
for normal operation. Temperature and threshold data are retained in standby mode.
10
N.C.
No Connection. Must be connected to ground.
11
OVERT
Overtemperature Active-Low, Open-Drain Output. OVERT asserts low when the temperature of
channels 1 and 4 exceed the programmed threshold limit.
12
V
CC
Supply Voltage Input. Bypass to GND with a 0.1礔 capacitor.
13
ALERT
SMBus Alert (Interrupt), Active-Low, Open-Drain Output. ALERT asserts low when the temperature of
any channel exceeds the programmed ALERT threshold.
14
SMBDATA SMBus Serial-Data Input/Output. Connect to a pullup resistor.
15
SMBCLK
SMBus Serial-Clock Input. Connect to a pullup resistor.
16
GND
Ground
Pin Description (continued)
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5253-1.85BC5 | IC REG LDO 1.85V .1A SC70-5 |
| MER1S4809SC | CONV DC/DC 1KVDC TH 1W 48-9V |
| EMC40DRXH-S734 | CONN EDGECARD 80POS DIP .100 SLD |
| NCP1217D100R2 | IC CTRLR PWM CM OVP HV 8SOIC |
| TAJS156K004RNJ | CAP TANT 15UF 4V 10% 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6622UE9A+ | 功能描述:板上安装温度传感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6622UE9A+T | 功能描述:板上安装温度传感器 5Ch Precision Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX66240ETA+ | 制造商:Maxim Integrated Products 功能描述:HF 4KBIT SHA-256 SECURE EEPROM - Rail/Tube |
| MAX66240ETA+T | 制造商:Maxim Integrated Products 功能描述:HF 4KBIT SHA-256 SECURE EEPROM - Tape and Reel |
| MAX6625PMTT+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL I2C 6TDFN EP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。