- 您现在的位置：买卖IC网 > Datasheet目录43 > MAX6626RMTT+T (Maxim Integrated)IC TEMP SENSOR I2C 6-TDFN Datasheet资料下载
参数资料
| 型号： | MAX6626RMTT+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/14页 |
| 文件大小： | 421K |
| 描述： | IC TEMP SENSOR I2C 6-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±1°C（最小值） |
| 拓扑： | ADC，比较器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WDFN 裸露焊盘 |
| 供应商设备封装： | 6-TDFN 裸露焊盘（3x3） |
| 包装： | 带卷 (TR) |
MAX6625/MAX6626
9-Bit/12-Bit Temperature Sensors with
I
2
C-Compatible Serial Interface in a SOT23
11
Maxim Integrated
drain, and the MAX6625R/MAX6626R output includes
an internal 35k& (typ) pullup resistor. Figure 6 shows
the OT alarm operation and reset details.
Fault Queue
A programmable fault queue on the MAX6625/
MAX6626 eliminates spurious alarm activity in noisy
environments. The queue sets the number of consecu-
tive out-of-tolerance temperature readings that must
occur before the OT alarm output is toggled. An out-of-
tolerance reading is above T
HIGH
or below T
LOW
. The
fault queue depth defaults to one at power-up and may
be programmed to one, two, four, or six consecutive
conversions. Any time the conversion result is in toler-
ance, and OT is not asserted, the queue is cleared,
even if it contains some out-of-tolerance counts.
Additionally, the fault queue automatically clears at
power-up, in shutdown, or if a master writes to any of
the T
HIGH
, T
LOW
, or configuration registers. Whenever
the fault queue is cleared, OT is deasserted.
For example, the fault queue is set to four, two consec-
utive out-of-tolerance readings have occurred, and the
master writes to the T
LOW
register. The fault queue is
cleared and begins to look for four new consecutive
out-of-tolerance conversions.
Comparator Mode
In comparator mode, OT is asserted when the number
of consecutive conversions exceeding the value in the
T
HIGH
register is equal to the depth of the fault queue.
OT deasserts when the number of consecutive conver-
sions less than the value in the T
LOW
register is equal
to the depth of the fault queue. T
HIGH
minus T
LOW
is
the effective hysteresis of the OT output.
For example, if T
HIGH
is set to +100癈, T
LOW
is set to
+80癈, and the fault queue depth is set to four, OT
does not assert until four consecutive conversions
exceed +100癈. Then, OT does not deassert until four
consecutive conversions are less than +80癈.
Comparator mode allows autonomous clearing of an OT
fault without the intervention of a master and is ideal to
use for driving a cooling fan (Figure 7).
Interrupt Mode
In interrupt mode, the MAX6625/MAX6626 look for a
T
HIGH
or a T
LOW
fault based on previous fault activity.
The OT pin asserts an alarm for an undertemperature
fault, as well as for an overtemperature fault, depending
on certain conditions. If the fault queue is cleared at
power-up, the IC looks for a T
HIGH
fault. After a T
HIGH
fault, the IC looks for a T
LOW
fault. After a T
LOW
fault,
the IC looks for a T
HIGH
fault, and it bounces back and
forth if properly deasserted each time. Once either fault
has occurred, it remains active indefinitely until
deasserted by a read of any register, and the device
then begins to look for a fault of the opposite type. Also,
if the fault queue is cleared, OT is deasserted and the
IC once again looks for a T
HIGH
fault. The activation of
any fault is subject to the depth of the fault queue.
DIE
TEMPERATURE
TIME
*
*
*
T
HIGH
T
LOW
OT
(COMPARATOR MODE)
OT
(INTERRUPT MODE)
TEMPERATURE RESPONSE
SHOWN WITH OT SET FOR
ACTIVE LOW
*THIS ASSUMES DEASSERTION OF OT BY A
MASTER THROUGH THE SERIAL INTERFACE.
SEE INTERRUPT MODE SECTION.
Figure 6. OT Alarm Output and Reset Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6627MKA#TG16 | IC TEMP SENSOR DGTL SOT23-8 |
| MAX6636UP9A+T | IC PREC TEMP MONITOR 7CH 20TSSOP |
| MAX6639FATE+ | IC 2CH TEMP MONITOR 16TQFN |
| MAX6641AUB92+ | IC TEMP MONITOR SMBUS 10UMAX |
| MAX6642ATT94+T | IC TEMP SENSOR SMBUS 6TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6626RMUT | 制造商:Maxim Integrated Products 功能描述:32-BIT TEMPERATURE SENSOR W/ I2C-COMPATIBLE S 6 PINS THNSOT - Rail/Tube |
| MAX6626RMUT+T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6626RMUT-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6627MKA | 制造商:Maxim Integrated Products 功能描述:REMOTE ?1?C ACCURATE DIGITAL TEMPERATURE SENSORS WITH SPI-CO - Bulk |
| MAX6627MKA#G16 | 制造商:Maxim Integrated Products 功能描述:REMOTE ?1?C ACCURATE DIGITAL TEMPERATURE SENSORS - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。