- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6872ETJ+ (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6872ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 34/48页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 类型： | 序列发生器 |
| 监视电压数目： | 6 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
SA7 through SA4 represent the standard interface
address (1010) for devices with EEPROM. SA3 and SA2
correspond to the A1 and A0 address inputs of the
MAX6872/MAX6873 (hard-wired as logic-low or logic-
high). SA0 is a read/write flag bit (0 = write, 1 = read).
The A0 and A1 address inputs allow up to four
MAX6872/MAX6873 devices to connect to one bus.
Connect A0 and A1 to GND or to the serial interface
power supply (see Figure 6).
Send Byte
The send byte protocol allows the master device to send
one byte of data to the slave device (see Figure 7). The
send byte presets a register pointer address for a sub-
sequent read or write. The slave sends a NACK instead
of an ACK if the master tries to send an address that is
not allowed. If the master sends 80h, 81h, or 82h, the
data is ACK. This could be start of the write byte/word
protocol, and the slave expects at least one further
data byte. If the master sends a stop condition, the
internal address pointer does not change. If the master
sends 84h, this signifies that the block read protocol is
expected, and a repeated start condition should follow.
The device reboots if the master sends 88h. The send
byte procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends an 8-bit data byte.
5) The addressed slave asserts an ACK on SDA.
6) The master sends a stop condition.
Write Byte/Word
The write byte/word protocol allows the master device
to write a single byte in the register bank, preset an
EEPROM (configuration or user) address for a subse-
quent read, or to write a single byte to the configuration
or user EEPROM (see Figure 7). The write byte/word
procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends an 8-bit command code.
5) The addressed slave asserts an ACK on SDA.
6) The master sends an 8-bit data byte.
7) The addressed slave asserts an ACK on SDA.
8) The master sends a stop condition or sends another
8-bit data byte.
9) The addressed slave asserts an ACK on SDA.
10) The master sends a stop condition.
To write a single byte to the register bank, only the 8-bit
command code and a single 8-bit data byte are sent.
The command code must be in the range of 00h to 45h.
The data byte is written to the register bank if the com-
mand code is valid. The slave generates a NACK at
step 5 if the command code is invalid.
To preset an EEPROM (configuration or user) address
for a subsequent read, the 8-bit command code and a
single 8-bit data byte are sent. The command code
must be 80h if the write is to be directed into the config-
uration EEPROM, or 81h or 82h, if the write is to be
SDA
1
0
1
0
A1
A0
X
R/W
ACK
START
MSB
LSB
SCL
Figure 6. Slave Address
34
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6874ETJ+ | IC SEQUENCE/SUPERVISOR 32TQFN |
| MAX6876ETX+ | IC TRACKER/SUPERVISOR MON 36TQFN |
| MAX6879ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6881ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6884ETP+ | IC SUPERVISOR PWR SPL 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6872ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6872ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6872ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6873ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6873ETJ+ | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。