- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6872ETJ+ (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6872ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 41/48页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 43 |
| 类型： | 序列发生器 |
| 监视电压数目： | 6 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
programmable outputs) connects to the reset input or a
nonmaskable interrupt of the μP.
Registers 3Ch–3Fh configure the watchdog functionality
of the MAX6872/MAX6873. Program each watchdog
timer to assert one or more programmable outputs (see
Tables 8–19). Program each watchdog timer to reset on
one of the GPI_ inputs, one of the programmable out-
puts, or a combination of one GPI_ input and one pro-
grammable output.
Each watchdog timer features independent initial and
normal watchdog timeout periods. The initial watchdog
timeout period applies immediately after power-up, after a
reset event takes place, or after enabling the watchdog
timer. The initial watchdog timeout period allows the μP to
perform its initialization process. If no pulse occurs during
the initial watchdog timeout period, the μP is taking too
long to initialize, indicating a potential problem.
The normal watchdog timeout period applies in every
other cycle after the initial watchdog timeout period
occurs. The normal watchdog timeout period monitors
processor behavior occurs. If no pulse occurs during
the normal watchdog timeout period, this indicates that
the processor has stopped operating or is stuck in an
infinite execution loop.
Disable or enable each initial timeout period through reg-
isters 3Ch and 3Eh. Registers 3Dh and 3Fh program the
initial and normal watchdog timeout periods, and enable
or disable each watchdog timer. See Tables 25 and 26
for a summary of the watchdog behavior.
Fault Detector
Registers 60h–62h store all fault conditions, including
undervoltage, overvoltage, GPI_, and watchdog timer
faults (see Table 27). Fault registers are read-only and
lose contents upon power removal. The first read com-
mand from the fault registers after power-up gives invalid
data. Any MR assertion writes to the fault register.
Reading the fault register clears all fault flags. Both GPI_
and WD_ bits assert if any of the GPI_ inputs are config-
ured as watchdog inputs (WD_) and a watchdog fault
occurs.
a pulsed output of the μP that indicates when normal
Table 25. Watchdog Inputs (Addresses 3Ch (Watchdog 1), 3Eh (Watchdog 2))
REGISTER
ADDRESS
EEPROM MEMORY
ADDRESS
BIT
RANGE
DESCRIPTION
Watchdog Input Selection:
00 = GPI1
[1:0]
[4:2]
01 = GPI2
10 = GPI3
11 = GPI4
Watchdog Internal Input Selection:
000 = PO1 (MAX6872), not used (MAX6873)
001 = PO2 (MAX6872), not used (MAX6873)
010 = PO3 (MAX6872), PO1 (MAX6873)
011 = PO4 (MAX6872), PO2 (MAX6873)
100 = PO5 (MAX6872), PO3 (MAX6873)
101 = PO6 (MAX6872), PO4 (MAX6873)
3Ch (watchdog 1)
3Eh (watchdog 2)
803Ch (watchdog 1)
803Eh (watchdog 2)
[6:5]
[7]
110 = PO7 (MAX6872), PO5 (MAX6873)
111 = PO8 (MAX6872), not used (MAX6873)
Watchdog Dependency on Inputs:
00 = 11 = Watchdog clear depends on both GPI_ from 3Ch[1:0]
(watchdog 1) or 3Eh[1:0] (watchdog 2) and PO_ from 3Ch[4:2]
(watchdog 1) or 3Eh[4:2] (watchdog 2).
01 = watchdog clear depends only on PO_ from 3Ch[4:2] (watchdog 1)
or 3Eh[4:2] (watchdog 2).
10 = watchdog clear depends only on GPI_ from 3Ch[1:0] (watchdog 1)
or 3Eh[1:0] (watchdog 2).
Initial Watchdog Timeout Period Enable:
0 = Disables initial watchdog timeout period (normal watchdog timeout
period not affected).
1 = Enables initial watchdog timeout period.
______________________________________________________________________________________
41
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6874ETJ+ | IC SEQUENCE/SUPERVISOR 32TQFN |
| MAX6876ETX+ | IC TRACKER/SUPERVISOR MON 36TQFN |
| MAX6879ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6881ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6884ETP+ | IC SUPERVISOR PWR SPL 20-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6872ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6872ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6872ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6873ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6873ETJ+ | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。