- 您现在的位置：买卖IC网 > PDF目录224188 > MAX6876ETX+T (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit PDF资料下载
参数资料
| 型号： | MAX6876ETX+T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | EEPROM-Programmable, Quad, Power-Supply Tracker/Sequencer Circuit |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC36 |
| 封装： | 6 X 6 MM, 0.80 MM HEIGHT, MO-220WJJD-1, TQFN-36 |
| 文件页数： | 3/39页 |
| 文件大小： | 425K |
| 代理商： | MAX6876ETX+T |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
MAX6876
EEPROM-Programmable, Quad,
Power-Supply Tracker/Sequencer Circuit
______________________________________________________________________________________
11
Pin Description (continued)
PIN
NAME
FUNCTION
7
OC
Active-Low, Open-Drain Overcurrent Output. OC asserts low if any monitored IN_ to OUT_ voltage
falls out of the selected percentage of the IN_ voltage range (VTH_OC) for more than the programmed
tOC. OC monitoring begins only after supply tracking or sequencing has been completed and is
disabled during power-down operation.
8
REM
Open-Drain Bus Removal Output. REM signals when it is safe to remove the card after a controlled
track/sequence-down operation. REM goes high impedance when all VOUT_ < VTH_PL. REM requires
an external pullup resistor. In master/slave mode, REM can be ORed together (the common REM
connection remains low if any VOUT_ > VTH_PL threshold) (see the Typical Application Circuit and the
Bus Removal Output (REM) section).
9
FAULT
Active-Low, Open-Drain Tracking Fault Alert Output or Input. FAULT asserts low if a tracking failure is
present for longer than the specified fault period or if tracking voltages fails by more than ±250mV
(see the FAULT section).
10
RESET
Active-Low, Open-Drain Reset or Power-Good Output. RESET is low during power-up and power-
down tracking. RESET goes high after all selected OUT_ outputs exceed their selected thresholds
and the reset timeout period tRESET has expired. The reset timeout period is internally selectable.
RESET requires an external pullup resistor.
11
ENABLE
Logic ENABLE Input. ENABLE must be high to enable voltage tracking/sequencing power-up
operation. OUT_ begins tracking down when ENABLE is low. Connect to ABP if not used.
12
MARGIN
Active-Low Margin Input. The MARGIN function allows systems to be tested with supply voltages
outside their normal ranges without affecting supply tracking/sequencing or reset states. MARGIN
functionality is usually enabled after systems have powered up in normal mode. The MARGIN
functionality is disabled (returns to normal monitoring mode) after MARGIN returns high. MARGIN is
internally pulled up to ABP through a 100k
resistor.
13, 23
N.C.
No Connection. Not internally connected.
14
MR
Active-Low Manual Reset Input. When MR is low, RESET goes low and remains asserted for the
selected timeout period after MR is pulled high. MR is internally pulled up to ABP through a 100k
resistor.
15
SDA
Serial-Interface Data Input/Output (Open-Drain). SDA requires an external pullup resistor.
16
SCL
Serial-Interface Clock Input. SCL requires an external pullup resistor.
17
A0
18
A1
Serial-Interface Address Inputs. The inputs allow up to four MAX6876 devices to be addressed when
sharing a common data bus. A1 and A0 should be connected to GND or ABP.
19
PG1
20
PG2
21
PG3
22
PG4
Power-Good Output, Open-Drain. Each PG_ output signals when its monitored OUT_ voltage is within
the selected percentage of the IN_ voltage range (VTH_PG). PG_ is low until OUT_ exceeds the
programmable threshold (VTH_PG) for more than tPOK. PG_ outputs are open-drain and require
external pullups if used.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX687CSA+T | High-Accuracy, Low-Dropout Linear Regulators |
| MAX6880ETG+T | Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors |
| MAX6881ETE+T | Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors |
| MAX6882ETE+T | Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors |
| MAX6883ETE+T | Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6876EVCMOD2 | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6877ETG | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6877ETG+ | 功能描述:监控电路 Triple Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6877ETG+T | 功能描述:监控电路 Triple Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。