- 您现在的位置：买卖IC网 > PDF目录224189 > MAX6884ETP+ (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC PDF资料下载
参数资料
| 型号： | MAX6884ETP+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC20 |
| 封装： | 5 X 5 MM, 0.80 MM PITCH, MO-220WHHC, QFN-20 |
| 文件页数： | 18/34页 |
| 文件大小： | 310K |
| 代理商： | MAX6884ETP+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Configuring the MAX6884/MAX6885
The MAX6884/MAX6885 factory-default configuration
sets all registers to 00h except for bits R91h[0],
R92h[0], R93h[0], R94h[0], R95h[0], which are set to 1.
This configuration sets all three programmable outputs
(RESET, UV/OV, WDO) as open drain, and RESET and
UV/OV dependent on MR (putting all outputs into high-
impedance states until the device is reconfigured by
the user). Each device requires configuration before full
power is applied to the system. Below is a general
step-by-step procedure for programming the
MAX6884/MAX6885:
1) Apply a supply voltage to IN1–IN4 or VCC, depend-
ing on the programmed configuration (see the
Powering the MAX6884/MAX6885 section). The
applied voltage must be 2.7V or higher.
2) Transmit data through the serial interface. Write to
the configuration registers first to ensure the device
is configured properly (see the Write Byte and
Block Write sections).
3) Use the read word protocol to read back the data from
the configuration registers to verify the data was writ-
ten (see the Receive Byte and Block Read sections).
4) Write the same data written to the configuration reg-
isters to the appropriate configuration EEPROM reg-
isters. After completing EEPROM configuration,
apply full power to the system to begin normal oper-
ation. The nonvolatile EEPROM stores the configura-
tion information while power is off.
Software Reboot
A software reboot restores the EEPROM configuration
to the volatile registers without cycling the power sup-
plies. Use the send byte command with data byte C4h
to initiate a software reboot. The 2.5ms (max) power-up
delay also applies after a software reboot.
MAX6884/MAX6885
EEPROM-Programmable, Hex
Power-Supply Supervisory Circuits
______________________________________________________________________________________
25
Table 12. Register Map (continued)
REGISTER
ADDRESS
EEPROM
MEMORY
ADDRESS
READ/
WRITE
DESCRIPTION
25h
—
R
ADC Conversion Data for AUXIN (2 LSBs) (Table 3)
26h
—
R
ADC Conversion Data for VCC (8 MSBs) (Table 3)
27h
—
R
ADC Conversion Data for VCC (2 LSBs) (Table 3)
28h
—
R
Fault Flags for Primary Voltage Detectors (Table 9)
29h
—
R
Fault Flags for Secondary Voltage Detectors (Table 9)
2Ah
—
R
Fault Flags for RESET, UV/OV, and WDO (Table 9)
REGISTER BANK
CONFIGURATION
EEPROM
USER EEPROM
CONFIGURATION
DATA
(R/W)
ADC AND FAULT
REGISTERS
(READ ONLY)
00h
17h
80h
40h
7Fh
97h
18h
2Ah
Figure 5. Memory Map
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6885ETP+ | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6886ETP+ | Pin-Selectable, Hex Power-Supply Supervisory Circuit |
| MAX6886ETP+T | Pin-Selectable, Hex Power-Supply Supervisory Circuit |
| MAX6887AETE+ | Hex/Quad, Power-Supply Supervisory Circuits |
| MAX6887AETE+T | Hex/Quad, Power-Supply Supervisory Circuits |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6884ETP+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884ETP+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884ETP-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884EVCMOD2 | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。