- 您现在的位置：买卖IC网 > PDF目录224189 > MAX6884ETP+ (MAXIM INTEGRATED PRODUCTS INC) EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC PDF资料下载
参数资料
| 型号： | MAX6884ETP+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC20 |
| 封装： | 5 X 5 MM, 0.80 MM PITCH, MO-220WHHC, QFN-20 |
| 文件页数： | 21/34页 |
| 文件大小： | 310K |
| 代理商： | MAX6884ETP+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
SA7 through SA4 represent the standard 2-wire inter-
face address (1010); for devices with EEPROM, SA2
corresponds to the A0 address inputs of the MAX6884/
MAX6885 (hardwired as logic-low or logic-high). SA0 is
a read/write flag bit (0 = write, 1 = read).
The A0 address input allows up to two MAX6884/
MAX6885s to connect to one bus. Connect A0 to GND
or to the 2-wire serial-interface power supply (see
Figure 10).
Send Byte
The send byte protocol allows the master device to send
one byte of data to the slave device (see Figure 11). The
send byte presets a register pointer address for a subse-
quent read or write. The slave sends a NACK instead of
an ACK if the master tries to send an address that is not
allowed or if the device is writing data to EEPROM or is
booting. If the master sends C0h, the data is ACK,
because this could be the start of the block write proto-
col, and the slave expects following data byte. If the mas-
ter sends a STOP condition, the internal address pointer
does not change. If the master sends C1h, this signifies
that the block read protocol is expected, and a repeated
START condition should follow. The device reboots if the
master sends C4h. The send byte procedure follows:
1) The master sends a START condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends an 8-bit data byte.
5) The addressed slave asserts an ACK on SDA.
6) The master sends a STOP condition.
Write Byte
The write byte protocol allows the master device to write a
single byte in the register bank or in the EEPROM (see
Figure 11). The write byte/word procedure follows:
1) The master sends a START condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends an 8-bit command code.
5) The addressed slave asserts an ACK on SDA.
6) The master sends an 8-bit data byte.
7) The addressed slave asserts an ACK on SDA.
8) The master sends a STOP condition.
To write a single byte to the register bank, only the 8-bit
command code and a single 8-bit data byte are sent.
The command code must be in the 00h to 2Fh range.
The data byte is written to the register bank if the com-
mand code is valid. The slave generates a NACK at
step 5 if the command code is invalid or any internal
operations are ongoing. To write a single byte of data to
the user or configuration EEPROM, the 8-bit command
code and a single 8-bit data byte are sent.
Block Write
The block write protocol allows the master device to
write a block of data (1 to 16 bytes) to the EEPROM or
to the register bank (see Figure 11). The destination
address must already be set by the send byte protocol
and the command code must be C0h. If the number of
bytes to be written causes the address pointer to
exceed 2Fh for the configuration register or 9Fh for the
configuration EEPROM, the address pointer stops
incrementing, overwriting the last memory address with
the remaining bytes of data. Only the last data byte
sent is stored in 17h (as 2Fh is read only and a write
cause no change in the content). If the number of bytes
to be written exceeds the address pointer 9Fh for the
user EEPROM, the address pointer stops incrementing
and continues writing exceeding data to the last
address. Only the last data is actually written to 9Fh.
The block write procedure follows:
1)
The master sends a START condition.
2)
The master sends the 7-bit slave address and a
write bit (low).
3)
The addressed slave asserts an ACK on SDA.
4)
The master sends the 8-bit command code for
block write (C0h).
5)
The addressed slave asserts an ACK on SDA.
6)
The master sends the 8-bit byte count (1 to 16
bytes) N.
7)
The addressed slave asserts an ACK on SDA.
8)
The master sends 8 bits of data.
9)
The addressed slave asserts an ACK on SDA.
10) Repeat steps 8 and 9 N - 1 times.
11) The master generates a STOP condition.
MAX6884/MAX6885
EEPROM-Programmable, Hex
Power-Supply Supervisory Circuits
28
______________________________________________________________________________________
SDA
1
00
0
A0
x
R/W
ACK
START
SCL
MSB
LSB
Figure 10. Slave Address
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6885ETP+ | EEPROM-Programmable, Hex, Power-Supply Supervisors with an ADC |
| MAX6886ETP+ | Pin-Selectable, Hex Power-Supply Supervisory Circuit |
| MAX6886ETP+T | Pin-Selectable, Hex Power-Supply Supervisory Circuit |
| MAX6887AETE+ | Hex/Quad, Power-Supply Supervisory Circuits |
| MAX6887AETE+T | Hex/Quad, Power-Supply Supervisory Circuits |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6884ETP+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884ETP+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884ETP-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884EVCMOD2 | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。