- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6889ETJ+T (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6889ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 29/40页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 序列发生器 |
| 监视电压数目： | 8 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
EEPROM-Programmable, Octal/Hex/Quad,
Power-Supply Sequencers/Supervisors
Table 23. Write Disable Register
REGISTER
ADDRESS
2Ch
2Dh
EEPROM
MEMORY
ADDRESS
ACh
ADh
BIT
RANGE
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[0]
[1]
[7:2]
DESCRIPTION
0 = Write is not disabled if PO1 asserts
1 = Write disabled if PO1 asserts
0 = Write is not disabled if PO2 asserts
1 = Write disabled if PO2 asserts
0 = Write is not disabled if PO3 asserts
1 = Write disabled if PO3 asserts
0 = Write is not disabled if PO4 asserts
1 = Write disabled if PO4 asserts
0 = Write is not disabled if PO5 asserts
1 = Write disabled if PO5 asserts
0 = Write is not disabled if PO6 asserts
1 = Write disabled if PO6 asserts
0 = Write is not disabled if PO7 asserts
1 = Write disabled if PO7 asserts
0 = Write is not disabled if PO8 asserts
1 = Write disabled if PO8 asserts
0 = Write is not disabled if PO9 asserts
1 = Write disabled if PO9 asserts
0 = Write is not disabled if PO10 asserts
1 = Write disabled if PO10 asserts
Not used
Configuring the
MAX6889/MAX6890/MAX6891
The MAX6889/MAX6890/MAX6891 factory-default con-
figuration sets all registers to 0h, except bits in Tables
17 and 18, which are set to 1h. Factory-default configu-
ration sets all PO_’s as active-high, open drain (all out-
puts are high impedance until the device is configured
by the user). Each device requires configuration before
full power is applied to the system. To configure the
MAX6889/MAX6890/MAX6891, first apply an input volt-
age to IN1, or one of IN2–IN5 or V CC (see the Powering
the MAX6889/MAX6890/MAX6891 section). V IN1 > 4V,
or one of V IN2 –V IN5 or V CC > 2.7V to ensure device
operation. Next, transmit data through the serial inter-
face. Use the block write protocol to quickly configure
the device. Write to the configuration registers first to
ensure the device is configured properly. After com-
pleting the setup procedure, use the read word or
block read protocol to read back the data from the con-
figuration registers. Lastly, use the write byte or block
write protocol to write this data to the EEPROM regis-
ters. After completing the EEPROM register configura-
tion, apply full power to the system to begin normal
operation. The nonvolatile EEPROM stores the latest
configuration upon removal of power. Write 0s to all
EEPROM registers to clear the memory.
Software Reboot
A software reboot allows the user to restore the EEPROM
configuration to the volatile registers without cycling the
power supplies. Use the send byte command with data
byte C4h to initiate a software reboot. The 3ms (max)
power-up delay also applies after a software reboot.
Configuration EEPROM
The configuration EEPROM addresses range from 80h
to AEh. Write data to the configuration EEPROM to auto-
matically set up the MAX6889/MAX6890/MAX6891 upon
power-up. Data is transferred from the configuration
EEPROM to the configuration registers when V CC
exceeds UVLO during power-up or after a software
______________________________________________________________________________________
29
相关PDF资料 |
PDF描述 |
|---|---|
| MAX688ESA+T | IC REG LDO 3.3V 1A 8-SOIC |
| MAX6894ETI+ | IC SEQUENCE/SUPERVISOR 28TQFN |
| MAX6898PALT+T | IC SEQUENCE/SUPERVISOR 6UDFN |
| MAX690AESA | IC MPU SUPERVISORY CIRCUIT 8SOIC |
| MAX691ACWE | IC MPU SUPERVISOR CIRCUIT 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6889EVCMAXQ | 功能描述:监控电路 EEPROM-Programmable Octal/Hex/Quad Power-Supply Sequencers/Supervisors RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6889EVCMAXQU | 功能描述:监控电路 Evaluation Kit/Evaluation System for the MAX6889 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6889EVCMODU | 功能描述:监控电路 EEPROM-Programmable Octal/Hex/Quad Power-Supply Sequencers/Supervisors RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6889EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX688CPA | 功能描述:低压差稳压器 - LDO High-Accuracy LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。