- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6889ETJ+T (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6889ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 34/40页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 序列发生器 |
| 监视电压数目： | 8 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页
EEPROM-Programmable, Octal/Hex/Quad,
Power-Supply Sequencers/Supervisors
Read Byte
The read byte protocol allows the master device to
read the register or an EEPROM location (user or con-
figuration) content of the MAX6889/MAX6890/MAX6891
(see Figure 8). The read byte procedure follows:
1) The master sends a Start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on the data
line.
4) The master sends 8 data bits.
5) The active slave asserts an ACK on the data line.
6) The master sends a repeated Start condition.
7) The master sends the 7-bit slave ID plus a read bit
(high).
8) The addressed slave asserts an ACK on the data
line.
9) The slave sends 8 data bits.
10) The master asserts a NACK on the data line
11) The master generates a Stop condition.
Note that once the read has been done, the internal
pointer is increased by one, unless a memory boundary
is hit.
If the device is busy or if the address is not an allowed
one, the command code is NACKed and the internal
address pointer is not altered. The master must then
interrupt the communication issuing a STOP condition.
Block Read
The block read protocol allows the master device to read
a block of 16 bytes from the EEPROM or register bank
(see Figure 8). Read fewer than 16 bytes of data by issu-
ing an early STOP condition from the master, or by gen-
erating a NACK with the master. Previous actions through
the serial interface predetermines the first source
address. It is suggested to use a send byte protocol,
before the block read, to set the initial read address. The
block read protocol is initiated with a command code of
C1h. The block read procedure follows:
1) The master sends a Start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends 8 bits of the block read com-
mand (C1h).
5) The slave asserts an ACK on SDA, unless busy.
6) The master generates a repeated Start condition.
7) The master sends the 7-bit slave address and a
read bit (high).
8) The slave asserts an ACK on SDA.
9) The slave sends the 8-bit byte count (16).
10) The master asserts an ACK on SDA.
11) The slave sends 8 bits of data.
12) The master asserts an ACK on SDA.
13) Repeat steps 8 and 9 15 times.
14) The master generates a Stop condition.
Address Pointers
Use the send byte protocol to set the register address
pointers before read and write operations. For the con-
figuration registers, valid address pointers range from
00h to 2Fh. Register addresses outside of this range
result in a NACK being issued from the MAX6889/
MAX6890/MAX6891. When using the block write proto-
col, the address pointer automatically increments after
each data byte, except when the address pointer is
already at 2Fh. If the address pointer is already 2Fh,
and more data bytes are being sent, these subsequent
bytes overwrite address 2Fh repeatedly. No data will
be left in 2Fh as this is a read-only address.
For the configuration EEPROM, valid address pointers
range from 80h to B7h (even if they are only meaningful
up to AEh). When using the block write protocol, the
address pointer automatically increments after each
data byte, except when the address pointer is already
at B7h. If the address pointer is already B7h, and more
data bytes are being sent, these subsequent bytes
overwrite address B7h repeatedly, leaving only the last
sent data byte stored at this register address.
For the user EEPROM, valid address pointers range
from 40h to 7Fh. As for the configuration EEPROM,
block write and block read protocols can also be used.
The internal address pointer will auto-increment up to
the user-EEPROM boundary 7Fh where the pointer will
stop incrementing. When writing, only the last data writ-
ten will be stored in 7Fh.
34
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX688ESA+T | IC REG LDO 3.3V 1A 8-SOIC |
| MAX6894ETI+ | IC SEQUENCE/SUPERVISOR 28TQFN |
| MAX6898PALT+T | IC SEQUENCE/SUPERVISOR 6UDFN |
| MAX690AESA | IC MPU SUPERVISORY CIRCUIT 8SOIC |
| MAX691ACWE | IC MPU SUPERVISOR CIRCUIT 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6889EVCMAXQ | 功能描述:监控电路 EEPROM-Programmable Octal/Hex/Quad Power-Supply Sequencers/Supervisors RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6889EVCMAXQU | 功能描述:监控电路 Evaluation Kit/Evaluation System for the MAX6889 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6889EVCMODU | 功能描述:监控电路 EEPROM-Programmable Octal/Hex/Quad Power-Supply Sequencers/Supervisors RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6889EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX688CPA | 功能描述:低压差稳压器 - LDO High-Accuracy LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。