- 您现在的位置：买卖IC网 > PDF目录15957 > MAX691ACWE+ (Maxim Integrated Products)IC MPU SUPERVISOR CIRCUIT 16SOIC PDF资料下载
参数资料
| 型号： | MAX691ACWE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISOR CIRCUIT 16SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 类型： | 备用电池电路 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.65V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
| 产品目录页面： | 1412 (CN2011-ZH PDF) |
Microprocessor Supervisory Circuits
Maximum V CC Fall Time
The V CC fall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/μs. A standard rule of thumb for filter
capacitance on most regulators is on the order of 100μF
per amp of current. When the power supply is shut off or
the main battery is disconnected, the associated initial
V CC fall rate is just the inverse or 1A/100μF = 0.01V/μs.
The V CC fall rate decreases with time as V CC falls expo-
nentially, which more than satisfies the maximum fall-time
requirement.
Watchdog Software Considerations
A way to help the watchdog timer keep a closer watch
on software execution involves setting and resetting the
watchdog input at different points in the program,
rather than “pulsing” the watchdog input high-low-high
or low-high-low. This technique avoids a “stuck” loop
where the watchdog timer continues to be reset within
the loop, keeping the watchdog from timing out. Figure
14 shows an example flow diagram where the I/O dri-
ving the watchdog input is set high at the beginning of
the program, set low at the beginning of every subrou-
tine or loop, then set high again when the program
returns to the beginning. If the program should “hang”
in any subroutine, the I/O is continually set low and the
watchdog timer is allowed to time out, causing a reset
START
SET
WDI
LOW
SUBROUTINE
OR PROGRAM LOOP
SET WDI
HIGH
RETURN
END
or interrupt to be issued.
Figure 14. Watchdog Flow Diagram
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX691ACSE+ | IC SUPERVISOR MPU 16-SOIC |
| M3CKK-6018R | IDC CABLE - MKC60K/MC60M/MPK60K |
| MAX693ACSE+ | IC SUPERVISOR MPU 16-SOIC |
| RP10-4815DE/N/M1 | CONV DC/DC 10W 36-75VIN +/-15V |
| M3AKK-6018R | IDC CABLE - MSC60K/MC60M/MPK60K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX691ACWE+ | 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX691ACWE+T | 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX691ACWE-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX691AEJE | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX691AEPA | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。