参数资料
| 型号： | MAX6953EAX+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/23页 |
| 文件大小： | 0K |
| 描述： | IC DRVR DSPL LED 36-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 显示器类型： | LED |
| 配置： | 5 x 7（矩阵） |
| 接口： | I²C |
| 数字或字符： | 4 位数字 |
| 电流 - 电源： | 12mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
2-Wire Interfaced, 2.7V to 5.5V, 4-Digit 5 ? 7
Matrix LED Display Driver
COMMAND BYTE IS STORED ON RECEIPT OF STOP CONDITION
D15
D14
D13
D12
D11
D10
D9
D8
ACKNOWLEDGE FROM MAX6953
S
SLAVE ADDRESS
0
A
COMMAND BYTE
A
P
Figure 7. Command Byte Received
R/W
ACKNOWLEDGE FROM MAX6953
ACKNOWLEDGE FROM MAX6953
ACKNOWLEDGE FROM MAX6953
HOW CONTROL BYTE AND DATA BYTE MAP INTO
MAX6953's REGISTERS
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
ACKNOWLEDGE FROM MAX6953
S
SLAVE ADDRESS
0
A
COMMAND BYTE
A
DATA BYTE
A
P
R/W
1 BYTE
AUTOINCREMENT MEMORY WORD ADDRESS
Figure 8. Command and Single Data Byte Received
read-after-write verification, reset the command byte's
address because the stored byte address generally is
autoincremented after the write (Table 4).
Operation with Multiple Masters
If the MAX6953 is operated on a 2-wire interface with
multiple masters, a master reading the MAX6953
should use a repeated start between the write, which
sets the MAX6953's address pointer, and the read(s)
that takes the data from the location(s). This is because
it is possible for master 2 to take over the bus after
master 1 has set up the MAX6953's address pointer but
before master 1 has read the data. If master 2 subse-
quently changes the MAX6953's address pointer, then
master 1's delayed read may be from an unexpected
location.
Command Address Autoincrementing
Address autoincrementing allows the MAX6953 to be
configured with the shortest number of transmissions
by minimizing the number of times the command byte
needs to be sent. The command address or the font
pointer address stored in the MAX6953 generally incre-
ments after each data byte is written or read (Table 4).
Digit Registers
The MAX6953 uses eight digit registers to store the char-
acters that the user wishes to display on the four 5 ? 7
LED digits. These digit registers are implemented with
two planes of 4 bytes, called P0 and P1. Each LED digit
is represented by 2 bytes of memory, 1 byte in plane P0
and the other in plane P1. The digit registers are mapped
so that a digit’s data can be updated in plane P0, or
plane P1, or both planes at the same time (Table 5).
If the blink function is disabled through the Blink Enable
Bit E (Table 10) in the configuration register, then the
digit register data in plane P0 is used to multiplex the
display. The digit register data in P1 is not used. If the
blink function is enabled, then the digit register data in
both plane P0 and plane P1 are alternately used to mul-
tiplex the display. Blinking is achieved by multiplexing
the LED display using data planes P0 and P1 on alter-
nate phases of the blink clock (Table 11).
The data in the digit registers does not control the digit
segments directly. Instead, the register data is used to
address a character generator, which stores the data of
a 128-character font (Table 15). The lower 7 bits of the
digit data (D6 to D0) select the character from the font.
The most-significant bit of the register data (D7) selects
whether the font data is used directly (D7 = 0) or
whether the font data is inverted (D7 = 1). The inversion
feature can be used to enhance the appearance of
bicolor displays by displaying, for example, a red char-
acter on a green background.
Display Blink Mode
The display blinking facility, when enabled, makes the
driver flip automatically between displaying the digit
register data in planes P0 and P1. If the digit register
data for any digit is different in the two planes, then that
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6954AAX | IC DRIVER LED SEG 14/16 36-SSOP |
| MAX6955ATL+T | IC DRVR DSPL LED 40-TQFN |
| MAX6956ATL/V+ | IC DRIVER LED PORT 20/28 40WQFN |
| MAX6957ANI | IC DRIVER LED PORT 20/28 28-DIP |
| MAX6959AAPE+ | IC DRVR DSPL LED 16-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6953EPL | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6953EPL+ | 功能描述:LED显示驱动器 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6954AAX | 功能描述:LED显示驱动器 2.7-5.5V LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6954AAX+ | 功能描述:LED显示驱动器 2.7-5.5V LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6954AAX+T | 功能描述:LED显示驱动器 2.7-5.5V LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。