- 您现在的位置：买卖IC网 > PDF目录20968 > MAX6965ATE+ (Maxim Integrated)IC LED DRIVER LINEAR 16-TQFN PDF资料下载
参数资料
| 型号： | MAX6965ATE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/22页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 9 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 400kHz |
| 电源电压： | 2 V ~ 3.6 V |
| 输出电压： | 7V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
9-Output LED Driver with Intensity Control
and Hot-Insertion Protection
Functional Overview
The MAX6965 is a general-purpose output (GPO)
peripheral that provides nine output ports, O0–O8, con-
trolled through an I 2 C-compatible serial interface. All out-
puts sink loads up to 50mA connected to external
supplies up to 7V, independent of the MAX6965’s supply
voltage. The MAX6965 is rated for a ground current of
190mA, allowing all nine outputs to sink 20mA at the
same time. Figure 1 shows the output structure of the
MAX6965. The outputs default to logic high (high imped-
ance unless external pullup resistors are used) on
power-up.
Output Control and LED Blinking
The blink phase 0 register sets the output logic levels of
the 8 outputs O0–O7 (Table 6). This register controls
the port outputs if the blink function is disabled. A dupli-
cate register, the Blink Phase 1 register, is also used if
the blink function is enabled (Table 7). In blink mode,
the outputs can be flipped between using the blink
phase 0 register, and the blink phase 1 register using
hardware control (the BLINK input) and/or software
control (the blink flip flag in the configuration register)
(Table 4).
OUTPUT
PORT
REGISTER
The 9th output, O8, is controlled through 2 bits in the
Configuration register, which provide the same static or
blink control as the other eight outputs (Table 4).
The logic level of the BLINK input may be read back
through the blink status bit in the configuration register
(Table 4). The BLINK input, therefore, may be used as
a general-purpose logic input (GPI port) if the blink
function is not required.
PWM Intensity Control
The MAX6965 includes an internal oscillator, nominally
32kHz, to generate PWM timing for LED intensity con-
trol. PWM intensity control can be enabled on an out-
put-by-output basis, allowing the MAX6965 to provide
any mix of PWM LED drives and glitch-free logic out-
puts (Table 8). PWM can be disabled entirely, in which
case all outputs are static and the MAX6965 operating
current is lowest because the internal oscillator is
turned off.
PWM intensity control uses a 4-bit master control and 4
bits of individual control per output (Tables 11 and 12).
The 4-bit master control provides 16 levels of overall
intensity control, which applies to all PWM-enabled out-
puts. The master control sets the maximum pulse width
from 1/15 to 15/15 of the PWM time period. The individ-
ual settings comprise a 4-bit number, further reducing
the duty cycle to be from 1/16 to 15/16 of the time win-
dow set by the master control.
For applications requiring the same PWM setting for all
DATA FROM
SHIFT REGISTER
WRITE PULSE
D
C K
FF
Q
Q
OUTPUT PORT
REGISTER DATA
Q2
I/O PIN
output ports, a single global PWM control can be used
instead of all the individual controls to simplify the con-
trol software and provide 240 steps of intensity control
(Tables 8 and 11).
GND
Figure 1. Simplified Schematic of I/O Ports
SDA
t LOW
t SU,DAT
t HD,DAT
t SU,STA
t HD,STA
t SU,STO
t BUF
SCL
t HD,STA
t R
t HIGH
t F
START CONDITION
REPEATED START CONDITION
STOP
CONDITION
START
CONDITION
Figure 2. 2-Wire Serial Interface Timing Details
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| REC8-2412SRW/H2/A/M/SMD-R | CONV DC/DC 8W 24VIN 12VOUT |
| P51-200-S-D-P-4.5V-000-000 | SENSOR 200PSI 7/16-20 UNF 4.5V |
| P51-300-A-C-I36-20MA-000-000 | SENSOR 300PSI M12-1.5 6G 4-20MA |
| P51-300-G-G-M12-4.5OVP-000-000 | SENSOR 300PSI 1/8-27NPT .5-4.5V |
| P51-2000-A-O-MD-20MA-000-000 | SENS 2000PSI 7/16-20 UNF 2B 20MA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6965ATE+ | 功能描述:LED显示驱动器 9-Output LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6965ATE+T | 功能描述:LED显示驱动器 9-Output LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6965ATE-T | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6965EVCMAXQU | 功能描述:LED 照明开发工具 9-Output LED Driver with Intensity Control RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX6965EVKIT | 功能描述:LED 照明开发工具 Evaluation Kit/Evaluation System for the MAX6965 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。